How to boot from a USB stick on a lenovo laptop

BIOS setup on Lenovo

After completing the preparation of the laptop for sale, it is configured to boot from the hard drive. The main problem with installing the OS on Lenovo is the enabled protection in the BIOS. Your task comes down to configuring the BIOS to disable autoloading from the hard drive and booting from a CD or flash drive.

Pre-turn off the laptop, if it is turned on, and do the following:

Lenovo Ideapad 320 Laptop | USB Boot & windows 10 installation

press the power button; wait 1-2 seconds (until the start screen appears on the display. the inscription LENOVO on a black background), then press the key on the keyboard several times to enter the BIOS menu. In modern models of Lenovo laptops, the same keys are responsible for entering the BIOS: the F2 button opens the service menu directly, the F12 button opens the boot device selection section.

The Delete button or a combination of Fn and keys from the “F” group can also work. it is specified for a specific model and is usually determined experimentally;

examining the navigation (information is given at the bottom of the display). The task is as follows: open the Security (Secure) section, from there go to the Secure Boot category and press the Enter key;

boot, stick, lenovo, laptop

configure Secure Boot to Disabled mode, i.e. disable protection;

press the Esc keyboard key to return to the main BIOS menu. From there we move to the Boot (Startup) section;

in the Boot section, the task boils down to configuring the laptop to boot from a CDROM or flash drive. To do this, move the appropriate option to the top of the list. Typically, the keyboard keys /. are used to change positions, but depending on the specific version, there may be differences. Check this point in the navigation information (found at the bottom of the BIOS setup menu);

press Esc, find the UEFI / Legacy Boot item and set it to Legacy Only mode (in some cases, this action has to be performed before performing the manipulations from the previous point, check it individually). Press the F10 button and confirm the desire to save the changes made by pressing Enter.

Lenovo S920 smartphone, characteristics of the fast IdeaPhone

Another interesting solution from Lenovo. the Lenovo IdeaPhone S920 smartphone.

  • screen: IPS 5.3 ″, 16 million colors, 1280 × 720, touch, capacitive, multitouch;
  • processor: 4-core MTK 6589, 1.2 GHz, PowerVR Series5XT video;
  • memory: 1 GB RAM, 4 GB built-in 32 GB microSDHC, microSD;
  • phone type: candy bar, 159 g, 154 × 77.7 × 7.9 mm;
  • phone charging connector: micro-USB;
  • communication type: GSM 900/1800/1900, 3G;
  • navigation: GPS, A-GPS;
  • interfaces: Wi-Fi, Bluetooth, USB;
  • platform: Andro IdeaPhone S920 boasts two SIM cards, but it is equipped with one radio module, which, for example, does not allow him to download a file on the Internet during a telephone conversation.

The image quality of the S920 is very good, but ideaDesktop does not shine with its design. The battery allows the smartphone to work intensively for a day on a single charge, which is a very good indicator. The speaker of the phone is of high quality and loud.

Lenovo IdeaPhone S920 is not an absolute bestseller, but it is a good choice if you buy an all-in-one device, which is emphasized by its good camera, long battery life and the phone has 2 SIM cards.

Booting Lenovo laptop from USB drive

There are two ways you can get your laptop to boot from a USB drive.

  • Through the Boot Menu (I recommend this method). With the help of this menu, we can tell the Lenovo laptop which device to boot from this particular time. Since starting the laptop from the bootable drive, we most likely need to do it only once. This is enough to start a Windows installation or perform other actions.
  • Through the BIOS menu. Here you need to change the boot order in the BIOS settings. Basically, nothing is complicated. But I see no reason to do this if you can select a device through the Boot Menu. Unless you can do it through the boot menu. Such a fallback.

Anyway, first connect the USB stick to the laptop.

It is desirable to connect to a USB 2.0 port. There can be problems with USB 3.0. The USB 3.0 port in the middle is usually blue, or lighter than USB 2.0.

Hey! Today I decided to prepare a simple, but at the same time very useful instruction, which should be useful to all Lenovo laptop owners. We will boot a Lenovo laptop from a USB flash drive. I have such a laptop, so I can show everything with a real example.

READ  Lenovo l340 touchpad not working

Since many models of modern laptops do not have a CD / DVD drive, many people have a question, how do you install Windows? How to boot a laptop for system recovery, virus checks, diagnostics, etc. All this can be done from a regular USB flash drive. over, if your laptop has a drive, then it is better to use a USB flash drive to install Windows or boot the laptop from some other boot disk. over, everyone has a flash drive, and a blank disk still needs to be found.

Booting a Lenovo laptop from a USB stick is as easy as booting from a disk. There is practically no difference.

First, we need to make a bootable USB flash drive. Simply put, write a.iso image of Windows, or another system / program to a USB drive. You can look at the example of creating a bootable drive with Windows 10. To write an.iso to a USB flash drive, I recommend using the following programs: Media Creation Tool (for downloading and recording Windows 10), WinSetupFromUSB, UltraISO, Rufus, Windows USB / DVD Download Tool. Of course, any computer can be booted from such a drive. Not only Lenovo.

Booting with UEFI boot

Sometimes the laptop boots up so quickly that the BIOS cannot be accessed by pressing the F1, F2Fn, or F12 button. If the laptop does not have a “Novo Button” button, but at the same time it can normally load the operating system from the hard disk, then you can enter the UEFI BIOS boot menu directly from Windows 8 / 8.1 / 10.

Changing the boot order of your laptop

You need to go into the BIOS again, not forgetting to first insert the USB flash drive into the laptop. Go to the Boot section. If you did everything correctly, you will see your USB flash drive in this window.

Here you need to prioritize the flash drive, raising it to the first place in the list. Just press the Fn and F6 keys at the same time. As you can see, the device name has changed its position.

Now click on Exit again and save all changes. The laptop will reboot and start booting from the USB stick. Do not forget to return the protection and make the rest of the settings, in the reverse order, after completing the work.

How to boot Lenovo laptop from USB stick?

Hey! Today I decided to prepare a simple, but at the same time very useful instruction, which should be useful to all Lenovo laptop owners. We will boot a Lenovo laptop from a USB flash drive. I have such a laptop, so I can show everything with a real example.

Since many models of modern laptops do not have a CD / DVD drive, many people have a question, how do you install Windows? How to boot a laptop for system recovery, virus checks, diagnostics, etc. All this can be done from a regular USB flash drive. over, if your laptop has a drive, then it is better to use a USB flash drive to install Windows or boot the laptop from some other boot disk. over, everyone has a flash drive, and a blank disk still needs to be found.

Booting a Lenovo laptop from a USB stick is as easy as booting from a disk. There is practically no difference.

First, we need to make a bootable USB flash drive. Simply put, write an.iso image of Windows, or another system / program to a USB drive. You can look at the example of creating a bootable drive with Windows 10. To write an.iso to a USB flash drive, I recommend using the following programs: Media Creation Tool (for downloading and recording Windows 10), WinSetupFromUSB, UltraISO, Rufus, Windows USB / DVD Download Tool. Of course, any computer can be booted from such a drive. Not only Lenovo.

Lenovo boot from flash drive

Nearly all laptop models available today do not ship with a built-in CD / DVD drive. Lenovo laptops are no exception. A bootable USB drive in this case is a useful tool for diagnosing and restoring the operating system or for installing a new OS.

There are several ways to boot Lenovo laptops from a bootable USB drive.

How to boot from USB (Lenovo B51-30 laptop)

Download using “Novo Button

If you cannot enter the Boot Manager boot menu with the F12 key, for this case, Lenovo notebooks have a special arrow button next to the power button or on their side panel. This button is present on many Lenovo laptops and is called “Novo Button”.

To activate the download using the “Novo Button” button, you need:

    Press it when the system is off.

Launching a Lenovo laptop from a USB flash drive via BIOS

To enter the BIOS, you must actively press the F2 key immediately after turning on the laptop. Or use “Novo Button Menu” for this, as I showed above. Read more in the article: How to enter the BIOS of a Lenovo laptop.

In the BIOS menu, go to the “Boot” section (using the left / right keys).

Next, you need to select our drive and use the F5 and F6 keys to put it in the first place in the list.

Again, there may be two partitions: EFI and Legacy. If you are going to install Windows and you have an EFI partition as in the screenshot above, and during installation you encountered the error “Installing Widnows on this disk is not possible. The selected disk contains a table of MBR partitions “, then you need to set the value” Legacy First “instead of” UEFI First “in the” Boot Priority “menu.

READ  The Laptop Screen Does Not Light Up When Turned On

And put “USB HDD” in the first place in the boot list, as I showed above.

Remember to save BIOS settings by pressing F10.

How to boot a Lenovo laptop from a USB flash drive?

How to enter BIOS on Lenovo laptop and boot from USB stick to UEFI BIOS

The other day they brought me a Lenovo IdeaPad B5030 laptop with Windows 8 installed. It was necessary to cure it of viruses. I inserted a USB flash drive with special antivirus software into it and tried to boot from it. This turned out to be not as easy as you think. The fact is that this laptop, like most other modern laptops (released in 2013, 2014 and later) has a UEFI BIOS. And in order to set a boot from a USB flash drive in such a BIOS, you need to strain a little

A laptop with a UEFI BIOS cannot be booted from a USB flash drive just like that, since it has special protection. the Secure Boot protocol, which is based on special certified keys (available only for Windows 8). Secure Boot will not allow you to boot your laptop from any boot disk or flash drive, except for the Windows 8 installation disk. Therefore, to boot a laptop from a USB flash drive, you must first disable this Secure Boot protocol in your laptop BIOS.

But even that is not all: as a rule, it is not enough to disable only one Secure Boot in the UEFI interface. It is also necessary to enable “compatibility with other operating systems”. It is called differently in different laptops: “CSM”, “CSM Boot”, “UEFI and Legacy OS”, “Legacy BIOS”, “CSM OS”. In Lenovo laptops it is called “Legacy Support”.

So, here’s how I booted a Lenovo laptop from a USB flash drive:

To get into the BIOS of a Lenovo laptop, immediately after turning it on, hold down two keys on the keyboard: FnF2:

Before us will open BIOS InsydeH20 Setup Utility, typical for most modern laptops (Lenovo, Acer, Toshiba).

Using the arrows on the keyboard, go to the Security section. Here we go down to the Secure Boot item and set it to the Disabled position:

Next, go to the Boot section. Here, opposite the Boot Mode item, UEFI will be displayed: We are changing it to Legacy Support. Here (under it), opposite the Boot Priority item, Legacy First is automatically displayed.

And now we leave from here, saving the changes made. To do this, go to the Exit section. Press Enter to select the Exit Saving Changes item. then click Yes:

Now we need to set the boot of the laptop from the flash drive. We insert our bootable USB flash drive into its free USB connector. We go back into the BIOS (holding down the FnF2 keys).

Go to the Boot section. Our flash drive will appear here (USB HDD item):

Using the FnF6 keys, we raise it to the first place in the list of boot devices:

Everything! After that, the laptop will already boot from the USB flash drive.

An important addition: if you were able to boot from the flash drive after that, but you cannot install Windows from it, because an error occurs: “It is impossible to install Windows on this disk. The selected disk has a GPT partition style “, then read my next article.

How to boot from a USB stick on a lenovo laptop

Now you will see in the photos how easy and simple it is to configure the BIOS on a Lenovo G505 laptop to boot from a USB flash drive or drive. In this example, I’ll show you how to boot from the drive. Similarly, you can also boot from a USB flash drive.

This laptop model comes with Windows 8, and as we already understand the BIOS is UEFI. But I liked the BIOS, so that it is possible to switch the hard disk from AHCI to IDE, but this is not the point.

Let’s go to the BIOS setup of the Lenovo G505 laptop.

If someone does not understand here is a photo. Small arrow button.

After pressing the button, the laptop turns on and a menu appears.

We will be interested in items 2 and 3 (“BIOS Setup” and “Boot menu”).

P.S.: 4 An item for restoring Windows from an image recorded on a hard drive, that is, if the hard drive has been changed or already reinstalled Windows bypassing System Recovery, then this item can be deleted =).

Go to “BIOS Setup” and see a brief description of the laptop. We are not interested in this.

Then go to the “Security” tab, do as in the photo.

Disable the option, “Secure Boot” to “Disabled”.

And now let’s move on to the interesting, this is the “Boot” tab.

And so, according to the default settings in the “BOOT” tab, we see that the BIOS is working in “UEFI” mode, below we do as in the photos

READ  How to take a screenshot on an ASUS Windows laptop

“Boot Mode” is transferred to the “Legacy Support” mode and another option appears.

Switch the “Boot Priority” option to the “Legacy First” mode.

And now we have almost finished configuring the BIOS to boot from a drive or flash drive on a Lenovo G505 laptop.

It remains for us to save the settings. To do this, go to the “EXIT” tab.

Here we select “Save Changes” and turn off the laptop from the button, or “Exit Saving Changes” and turn it off with the power button. In the future, I will explain why it is necessary to do this.

And also, why was it necessary to turn off the laptop? I showed the settings for disabling “UEFI” and with the ability to boot from a USB flash drive or drive, but at the same time I did not give out the initial priority for starting the laptop. it took again a restart for the devices to appear.

Thus, making it easier and easier for us to boot from a USB flash drive or drive.

After turning off the laptop, again press the Recovery button (which is with an arrow). Here we will no longer enter the “BIOS Setup”, but go to the “BOOT Menu” tab.

Select and press “Enter” and voila, we see all the devices from which we can boot.

P.S.: The flash drive will be signed as USB HDD.

That’s the whole setup for a Lebovo G505 laptop to boot from a USB flash drive or drive.

Boot via BIOS

Booting from a USB drive (flash drive) by changing the BIOS boot priority is the best option when you need to unlock a PC using a Windows password recovery tool or fix a boot problem such as a blue screen, no OS startup, etc.

    Connect bootable USB drive to laptop USB port.

Reference! It is advisable to connect a USB storage device to a USB 2.0 port, since there may be a problem with the USB 3.0 port. USB 3.0 ports are usually blue in the middle, or lighter in color than USB 2.0 ports.

BIOS Boot

Reference! If the hard disk contains a table of MBR partitions (the old version of the partitioning of the HDD, working with partitions not exceeding 2 TB), then setting in “Boot Priority”. “UEFI First” may lead to an error installing Widnows.

Lenovo IdeaPad Z580 laptop: home machine at the right price

If you’re looking to purchase a laptop that combines style and entertainment at an affordable price, the Lenovo IdeaPad Z580 is a great choice. Attractive appearance, good ergonomics, durable case, excellent performance. all these qualities are possessed by a laptop from Lenovo.

The build quality of the Z580 is also good, and despite some pliability of the plastic panels (the laptop comes in both aluminum and plastic cases), the chassis is quite solid. The laptop offers bold, glossy lines, making it one of the brightest budget laptops on the market.

Beneath the attractive design of the IdeaPad Z580 are:

  • processor: Intel Core i3 / i5 / i7, 2200-2900 MHz;
  • core: Ivy Br Impressive and glossy display from Lenovo. With a screen diagonal of 15.6 ″, the matrix resolution is standard and is 1366 × 768 pixels. The brightness of the monitor is also average, but the contrast reaches an impressive 260: 1, which, along with good color reproduction, provides vibrant colors and makes it one of the best displays in its price category.

The laptop, not lightweight, is 33mm thick and weighs about 2.5kg. Battery life. 5 h.

Important! In real-world gaming tests, this is one of the fastest budget notebooks around. If the buyer wants a fast laptop for everyday tasks without the extra investment, the Lenovo IdeaPad Z580 won’t disappoint.

Phoenix. Award BIOS

If Phoenix. Award BIOS is installed on the laptop, after the standard entry into the BIOS, you must:

    Use the up and down arrows to select “Advanced BIOS Features” and enter it by pressing “Enter”.

How to boot a Lenovo laptop from a USB flash drive

In the lower left corner of the screen we see the inscription “To interrupt normal startup, press Enter Button” (To interrupt normal startup, press the Enter button), respectively, while the inscription on the screen is lit, press Enter.

And a window appears in which we must select an action:

ESC. Continue loading the operating system.

F11. Start to rollback laptop to factory settings.

F12. Select a device to boot the laptop (this is what we need).

A window opens in which you can select:

Launching a factory rollback program.

Nearly all laptop models available today do not ship with a built-in CD / DVD drive. Lenovo laptops are no exception. A bootable USB drive in this case is a useful tool for diagnosing and restoring the operating system or for installing a new OS.

There are several ways to boot Lenovo laptops from a bootable USB drive.

For Windows 8 / 8.1

  • Move the mouse pointer to the upper or lower right corner of the display, and move the mouse up or down. The “Charm” panel will appear, where you need to click “Options” (gear icon).
BICBON.COM 2021