How to connect a second monitor to the motherboard

How to connect two monitors to a laptop with VGA and HDMI?

If you have the most common computer monitor, simply connect it to your laptop via HDMI, DisplayPort, or VGA. On most laptops, the [Fn] [F] key combination is used to set up multiple monitors. In this menu, you can choose whether only one screen will be used or all at once.

How to connect multiple monitors to one video card?

To combine 3 monitors into one system, one of them must be connected via DisplayPort or miniDisplayPort (miniDP), the second via DVI, and the third via VGA, HDMI or the same DVI. If there are 4 monitors, two devices must be connected to DisplayPort, the third to DVI, and the fourth to VGA or HDMI. 5 May 2020.

Is it possible to connect a second monitor to the integrated video card?

In order to connect a second monitor, you must have a video card with two (or more) video outputs. In this case, you will have to buy a discrete graphics card to create a configuration with two monitors. As for video outputs, they can be of several types: DVI, VGA, DisplayPort or HDMI.

Is it possible to connect a monitor without a video card?

It is possible to achieve that the computer works without a video card only if there is a built-in workable card on the motherboard, processor. External devices are also used.

How to connect a second monitor via Windows 10 motherboard?

The connection is carried out as follows:

  • Disconnect PC.
  • Examine the back of the system unit → locate the horizontally located VGA / DVI / HDMI / DP video adapter connector.
  • Connect an additional monitor to the video card slot.
  • Connect the extra shield to a power source.
  • Turn on your computer.

How to connect a second monitor through a monitor?

How to connect two monitors to a computer?

  • Make sure you can connect multiple monitors to your computer.
  • Find out what video connectors are on the video card and monitors.
  • Buy the cables you need (if not available).
  • Turn off your computer.
  • Connect the first monitor to one of the video card connectors.
  • Connect a second monitor.

How to set up two monitors in Windows 10?

  • Make sure cables are properly connected to new monitors.
  • Choose how the desktop is displayed.
  • Right-click anywhere on the desktop and select Display Settings to open the Display page.

Step 1: connect buttons and indicators

This stage is vital for the computer to work, so it needs to be done first. Before starting work, it is recommended to disconnect the computer from the mains to avoid a sudden power surge.

A special block is allocated on the motherboard, which is intended only for arranging the wires of indicators and buttons. It is called “Front panel”, “PANEL” or “F-PANEL”. On all motherboards, it is signed and located at the bottom, closer to the intended location of the front panel.

Let’s consider the connecting wires in more detail:

  • Red wire. designed to connect the on / off button;
  • Yellow wire. connects to the computer restart button;
  • The blue cable is responsible for one of the system status indicators, which usually glows when the PC is restarted (on some case models this is not);
  • The green cable is used to connect the motherboard to the computer’s power indicator.
  • White cable is needed to connect power.

connect, second, monitor, motherboard

Sometimes the red and yellow wires “change” their functions, which can be confusing, so it is advisable to study the instructions before starting work.

The places for connecting each wire are usually marked with the corresponding color or have a special identifier, which is written either on the cable itself or in the instructions. If you do not know where to connect this or that wire, then connect it “at random”, because then you can reconnect everything.

To check if the cables are connected correctly, connect the computer to the network and try to turn it on using the button on the case. If the computer turns on and all the indicators are on, then you have connected everything correctly. If not, then unplug the computer again and try swapping the wires, perhaps you just installed the cable on the wrong connector.

Connecting the front panel to the motherboard

Most inexperienced computer users find that connecting the front panel of the computer case, which contains the power and restart buttons, as well as USB inputs and audio outputs, to the motherboard is a difficult and difficult task.

But, as often happens, after spending 5 minutes studying the issue, everything becomes clear and very doable. In this article, we will look at the sequence of steps that must be performed to successfully and correctly connect the front panel to the motherboard, be it a motherboard from Asus, Gigabyte, Asrock, MSI, or others.

READ  Monitor input is not supported what to do

Step 3. Connect the front panel connectors to the corresponding connectors on the motherboard

Further, there are 2 possible options for the development of the situation.

Stage 2: connecting the rest of the components

At this stage, you need to connect the connectors for USB and the speaker of the system unit. Some housings do not include these elements on the front panel, so if you didn’t find any USB ports on the case, you can skip this step.

The places for connecting the connectors are located near the slot for connecting buttons and indicators. They also have certain names. F_USB1 (the most common version). It should be borne in mind that there can be more than one of these places on the motherboard, but you can connect to any one. The cables have the corresponding signatures. USB and HD Audio.

Connecting the USB input wire looks like this: take a cable labeled “USB” or “F_USB” and connect it to one of the blue connectors on the motherboard. If you have a USB 3.0 version, then you will have to learn more about Honor. in this case, you will have to connect the cable to only one of the connectors, otherwise the computer will not work correctly with USB drives.

Similarly, you need to connect the HD Audio audio cable. The connector for it looks almost the same as for the USB outputs, but it has a different color and is called either AAFP or AC90. Usually located near the USB connection. On the motherboard, he is only one.

Connecting the front panel elements to the motherboard is easy. If you make a mistake in something, then it can be corrected at any time. However, if you do not correct this, the computer may not function correctly.

We are glad that we were able to help you solve the problem.

Option one

On your motherboard, all the contacts are signed and you simply put the chips on the contacts, observing the corresponding names and polarity. Polarity is important for HDD LED (IDE LED) and Power LED. On the board, the positive contact is labeled as “”, and on the chip, the positive contact is a colored wire (other than white and black). Or, if all the wires from the front panel are black, then “” will also be signed on them.

Polarity and. when PLED and HDLED are connected

Even if you mix up the polarity, then nothing terrible will happen. It’s just that when you turn it on, the power button will not light up and the hard disk activity LED will not blink. In this case, simply turn the non-working chip upside down on the mat contacts. boards to reverse polarity.

Important information

First, examine the appearance of each free connector on the system board, as well as the cables for connecting the front panel components. When connecting, it is important to follow a certain sequence, because if you connect one or another element in the wrong order, then it may work incorrectly, not work at all, or disrupt the operation of the entire system.

Therefore, it is important to study the location of all elements in advance. It will be very good if there is an instruction or other paper for the mother card explaining the sequence of connecting certain components to the board. Even if the documentation for the motherboard is in a language other than Russian, do not throw it away.

It is not difficult to remember the location and name of all elements, because they have a certain appearance and are marked. It should be remembered that the instructions given in the article are general in nature, so the location of some components on your motherboard may be slightly different.

Step 1. find the cables going from the front panel to the mat. board

These are the same cables that we will connect to the corresponding connectors on the motherboard. The peculiarity of these very cables, by which they can be found among other wires in the case of the system unit, is the inscriptions at the ends of their connectors:

  • Power SW (PWRBTN). Computer power button;
  • Reset SW (Reset). Reset button;
  • HDD LED (IDE LED) (HDLED). hard disk activity indicator;
  • Power LED (PLED). Indicator of turning on the computer;
  • USB1.USBn. USB ports on the front panel;
  • Speaker (SPK). System speaker (speaker);
  • AUDIO (Mic, SPK L, SPK R, GND) (AAFP). Front panel headphone and microphone outputs.
READ  No signal detected on the monitor what to do

System unit front panel connectors

For those whose Power LED consists of 2 chips for 2 and 3 pins (as in the figure above), the rationale is as follows: on some motherboards, the POWER LED connection connector (computer power on indicator) is made on 3 pins (the middle one is not used ), and on some two. Therefore, in your case, you need to use either one Power Led chip or another.

How to connect two monitors to a computer

In this manual. in detail about connecting two monitors to a computer with Windows 10, 8 and Windows 7, setting up their work and possible nuances that you may encounter when connecting. See also: How to connect a TV to a computer, How to connect a laptop to a TV.

Setting up dual monitors on a Windows 10, 8 and Windows 7 computer

After turning on the computer with two monitors connected to it, they, after booting, are usually detected by the system automatically. However, it may turn out that the first time you load the image will not be on the monitor on which it is usually displayed.

After the first launch, it remains only to configure the mode of operation of two monitors, while Windows supports the following modes:

  • Screen mirroring. the same image is displayed on both monitors. In this case, if the physical resolution of the monitors is different, there may be problems in the form of image blur on one of them, since when the screen is duplicated for both monitors, the system sets the same resolution (and this cannot be changed).
  • Displaying an image only on one of the monitors.
  • Expand screens. when you select this option for two monitors, the Windows desktop “expands” to two screens, ie. the second monitor is the continuation of the desktop.

The operating modes are configured in the Windows screen parameters:

  • In Windows 10 and 8, you can press the WinP (Latin P) keys to select the monitor mode. When you select Extend, the desktop may appear to have “expanded in the wrong direction”. In this case, go to Settings. System. Display, select the monitor that is physically located on the left and check the box “Set as the main display”.
  • In Windows 7 (it is also possible to do it in Windows 8) go to the screen resolution settings of the control panel and set the desired operating mode in the “Multiple displays” field. If you select “Expand These Screens”, it may turn out that parts of the desktop are “swapped” in places. In this case, select in the display settings the monitor that is physically located on the left and at the bottom click “Make the main display”.

In all cases, if you are having problems with the clarity of the image, make sure that each monitor is set to its physical screen resolution (see How to change the screen resolution of Windows 10, How to change the screen resolution in Windows 7 and 8).

Connecting a second monitor to a video card

In order to connect two monitors to a computer, you need a video card with more than one output for connecting a monitor, and these are practically all modern discrete video cards from NVIDIA and AMD. In the case of laptops, they almost always have an HDMI, VGA or, more recently, Thunderbolt 3 connector for connecting an external monitor.

In this case, it will be required that the outputs of the video card are those that your monitor supports for input, otherwise adapters may be required. For example, if you have two old monitors with only VGA input, and the video card has a set of HDMI, DisplayPort and DVI, you will need the appropriate adapters (although, perhaps a better solution here would be to replace the monitor).

Note: From my observation, some novice users are unaware that their monitor has more inputs than it uses. Even if your monitor is connected via VGA or DVI, please note that there may be other inputs on its back that can be used, in which case you just have to purchase the necessary cable.

Thus, the initial task is to physically connect two monitors using the available video card outputs and monitor inputs. It is better to do this with the computer turned off, while it would also be wise to turn it off from the power supply.

If it is impossible to make the connection (there are no outputs, inputs, adapters, cables). it is worth considering options for purchasing a video card or monitor suitable for our task with the necessary set of inputs.

Additional Information

In conclusion. a few additional points that may be useful when connecting two monitors or just for information.

  • Some graphics adapters (in particular, Intel) as part of the drivers have their own settings for configuring the operation of multiple monitors.
  • In the “Expand screens” option, the taskbar is available on two monitors at the same time only in Windows In previous versions, this is only possible with the help of third-party programs.
  • If you have a Thunderbolt 3 output on a laptop or PC with integrated video, you can use it to connect multiple monitors: there are not many such monitors on sale yet (but soon they will be and they can be connected “in series” to one another), but on the other hand there are devices. docking stations connected via Thunderbolt 3 (in the form of USB-C) and having multiple monitor outputs (in the image Dell Thunderbolt Dock, designed for Dell laptops, but compatible not only with them).
  • If your task is to duplicate images on two monitors, while the computer has only one monitor output (integrated video), you can find an inexpensive splitter (splitter) for this purpose. Just search for a VGA, DVI or HDMI splitter on the market depending on the output you have.
READ  What to do if there is a dead pixel on the monitor

This, I think, can be completed. If you still have questions, something is not clear or does not work. leave comments (if possible, detailed), I will try to help.

We connect the second hard drive to the computer

On your own and without the involvement of a specialist, if necessary, you can connect an additional hard drive to your computer. Next, we will analyze the installation scheme and the subsequent connection of a new hard drive in the system unit. It should be noted that actions are carried out smoothly, clearly, without the use of force and abrupt actions.

The first step is to de-energize the entire system unit, for this we turn off the power, and then disconnect absolutely all the wires. Next, the side covers are unscrewed and removed, as in the image.

For the hard drive, of course, its own compartments are provided, which, depending on the model of the system unit, can be located in different positions and have different positions.

By the method of connecting the hard drive directly to the motherboard, they are divided into two types, namely SATA and IDE. The second option, which has very wide loops and ports for connection, is considered obsolete and is now used extremely rarely. Due to its irrelevance IDE variation will not be considered here.

If the SATA hard drive is already connected to the computer, then adding a second one can be quick and easy. The additional disk is inserted into a suitable free slot and secured to the chassis. It is desirable that they are located at a sufficient distance from each other to avoid overheating.

In order to connect the new hard drive to the motherboard itself, you need a SATA cable. Plug one end into the corresponding slot on the board, and the other to the hard drive.

It should be noted that in every modern model of the system unit, at least two SATA connectors are provided.

The next step is to connect the new hard drive directly to the power supply. For this, a special cable is used, the plug of which is somewhat wider than that of a SATA cable. In the case when a single plug comes out of the power supply, a splitter is needed. It happens that a narrow plug in the power supply was not provided, then an adapter should be purchased. Examples are shown in the images:

Having obtained all the above cables, you should connect the hard drive with the power cable.

The auxiliary media is now fully connected. You can then start up the computer by attaching the covers, plugging in cables, and applying power. After that, if necessary, the stage of system configuration of the new hard disk will follow.

| Contacts | Content | RSS