How to fix iPhone charging wire

How to disassemble charging from iphone 4

Many are worried about the question of How to disassemble the charger from the iPhone 4, because over time it breaks down and needs to be replaced or repaired, which in some cases can be done at home. Now all over the world there is a single standard according to which all chargers are manufactured on the basis of USB. It should be borne in mind that port 2.0 is capable of delivering voltage up to 0.5 A, while many devices consume much more.

For this reason, manufacturers have switched to more modern and complex formats. The network adapters produced now provide 4 contacts, or more precisely, the “zero” contact, the power contact, as well as a pair of informational ones. The latter are used in modern devices to identify the charger. In the future, the power controller determines the “fast” or “slow” charging mode.

You can fix a broken charger yourself, but for this you need to acquire some tools and do everything carefully.

iphone, charging, wire

With the modern pace of life, you often find yourself in situations where you need to urgently charge your iPhone, but this can only be done using the original charger. If it fails, then you can disassemble the case and replace the damaged part with a new one.

It is not very difficult to disassemble the iPhone charging, for this you need the following tools:

  • Screwdriwer set;
  • Sharp stationery knife;
  • Glue;
  • Fuse.

You need to disassemble the iPhone charging on a prepared table, covering it with sheets of white paper. It will be easy to find small bolts and details on it. Place a table lamp next to it and turn it on. Examine the charger carefully and determine the type of connection of the parts of its case. If the parts are fastened with screws, then they should be unscrewed with gentle movements. But in some cases you will have to tinker a lot, especially when it comes to the manufacturer’s new charge, in which there are no bolts.

If they do not give in well, then do a few turns in the opposite direction, and then continue to unscrew. Find all the plastic clips holding the iPhone charging case. They can be closed or hidden. If your charger has open latches, then you need to carefully squeeze the tabs out of the grooves. And if the latches are closed, then you need to press in the places where they are installed. You will also need to pry part of the iPhone charging with the tip of a flat screwdriver and remove it.

How to fix iPhone 4 charging?

first measure the voltage at the charging output!
it should be as shown in the picture. for convenience, you can take an unnecessary USB cable and cut it (so it will be easier to measure the voltage in the future, it can also be useful for convenience) further:
if there is no voltage at the output of the USB charging connector, then proceed to disassemble it.
you can disassemble using.
a jigsaw or a blade saw carefully along the red dotted line (there is a pitfall, Condenser. DO NOT SAW IT RANDOMLY) (the place where it stands is marked in the figure)

after sawing we get the following picture: At the input in front of the diode bridge there is a fuse resistor (it first of all flies out when there is a voltage drop in the network) we check it first!
If dead, change.
Resistor 10 Ohm 1W. 7 rubles.
Next, the diode bridge.
If punched, we change.
Diode bridge MB8S. 14 rubles.

After replacement, the voltage at the output of the USB connector appeared.
In total, the repair took me 21 rubles. instead of 1.500 rubles. for a new branded network adapter!

Next, we start assembling:
Since I sawed not very carefully and used a canvas, and not a jigsaw, I still have a gap of 1-1.5 mm (unfortunately I cannot show, I have already assembled it).
Did the following:
I took an unnecessary UDMA 66 cable, cut off the strip: Next, I carefully glued it with super-glue at the seam on the charge. In the end, it turned out like this:

We do it carefully and before plugging the phone into the charger, “500” times check the voltage at the USB output of the charging connector, so that nothing shorts anywhere and the voltage corresponds to that shown in the first figure.

Post has been editedmfilonen2. 13.04.16, 19:17

IPhone Cable Repair. Method One

In addition to the damaged wire with a connector, we need a heat-shrinkable tube, or heat shrink. In fact, it is a thin-walled soft plastic tube that is used just when it is necessary to insulate cables. To fix a charger or other cable, a heat-shrinkable tube is put on and heated to at least 70 degrees, and then it contracts, tightly fitting the contours of the wire. The main thing here is to choose the right tube diameter for the cable.

  • Cut a piece of heat shrink so that its length is equal to the distance between the beginning of the cable and the point of wear. Leave a margin of 1 cm.
  • Place the heat shrink on the connector. You can fix it with duct tape.
  • Begin to warm up the tube by placing it under some powerful heat source: a gas or electric stove, a gas burner or an ordinary lighter. You need hot air, not a flame. do not try to light the pipe under any circumstances.

That’s all, the cable was repaired, and now the charger will work!

There is another way, how to fix iPhone charging by replacing the cable and keeping the Lightning connector. You will have to tinker with it a little longer, but the result will be more durable, since the cable from the iPhone itself may wear out later in another place, and it will have to be repaired again.

How to disassemble iPhone charging

It will be much more difficult to disassemble a disposable charger, the body of which is monolithic. It is she who is equipped with the latest iPhone models. In this case, you will have to take a knife and cut the plastic. Carefully using a sharp knife, cut off one of the parts of the plastic case. Be extremely careful not to damage internal components. Replacing the fuse will have to glue both parts.

Remember that you should use a repaired charger with extreme caution, as it can lead to a short circuit.

READ  How to change the password on iPhone 5s

This is due to the fact that such chargers are not designed for repair and long-term use. If you do not have a fuse for the iPhone charger at hand, and you need to fix it as soon as possible, then use ordinary wire. Use it to close the contacts of the fuse connector. After that, charging should proceed in standard mode. But remember that this method should only be used if absolutely necessary.

Install a working fuse as soon as possible.

How to fix an iPhone cable with your own hands?

How to fix an iPhone charger is a frequent question for owners of Apple technology with Lightning connectors. Their fragility is due to the unreliable insulation of the wire: if it wears out in the bend area, the entire cable deteriorates. And it will not be easy to buy a new charger, since you will have to spend a lot on the original charging from the iPhone. otherwise the use of uncertified Lightning cables and accessories on iOS 7 is blocked by the manufacturer. Therefore, today we will figure out how to fix the charging with our own hands, keeping the cable from the iPhone.

How to fix a charger. method number 2

To fix iPhone charging in this way, you need to find some unnecessary USB cable, for example, from a mouse. The course of action is as follows:

  • Cut the wire from the iPhone at the place of damage and leave only the part with the Lightning connector for further work. Strip off some of the insulation, remove the metal braiding and strip the wiring.
  • Cut one of the connectors from the old USB cable and strip its wires in the same way.
  • Decide for yourself where on both cables there are red, white, green wiring and grounding, because then you will have to solder them.
  • After that, the ends of each wiring both at the Lightning connector and at the wire from the mouse must be cleaned and tinned. Heat the soldering iron, dip its tip in rosin, then in solder and press it against the wiring that needs to be tinned so that the entire tip is covered with solder. Do the same with all the wiring.
  • Pull the heat-shrink tubing onto the USB cable at this stage, otherwise you won’t be able to do it later. For each tinned wire of this cable, also put on a small heat shrink.
  • Start soldering wires together.
  • Shrink the mini heat shrinks by heating them with, say, a lighter.
  • Wrap the joint of the wires with electrical tape so that the heat shrinkage can easily sit on top, and everything looks more aesthetically pleasing. Slide the tube over the wire and heat it to the desired shape.

The cable was repaired, it remains only to check its performance. As you can see, the iPhone reacted to the connection and showed the beginning of charging, and the USB tester gave an indicator of 800 mA. and this is almost the indicator of the original iPhone charging. Use for health!

Another way to avoid the high costs of fixing your iPhone charger and extend its lifespan is to fix it with an interesting weave. See details in

What to do if your iPhone charger breaks down

The input voltage is kept in the range of 100-240V. The output is 1A 5V. It’s even strange how the manufacturer managed to fit a full-fledged power supply in such a compact case. In newer models, the case cannot be disassembled without damaging it. It is monolithic, and therefore will have to be cut. Even where plastic of a different color is visible, the construction is one-piece. this is just a decoration.

Soldering

If the damage cannot be repaired with insulation, you can resort to using a soldering iron.

    Remove some outer insulation and strip the wires as shown in the picture.

Do not use this method if you are unsure of your abilities; improper installation may damage the phone itself.!

Breakdown reasons

As a rule, damage to the charging cable appears at the folds near the connectors. The main reasons for this problem are: careless use or storage of an already fragile cord, as well as pets who love to play with all kinds of wires.

Insulating tape

Perhaps this is the easiest way. As soon as you notice the slightest violation of the insulation of the wire, you urgently need to stop the spread of the damage. To do this, you need to take a simple electrical tape and wrap the cable in tight rings in the place of damage, and then carefully cut off the excess. It will not look very aesthetically pleasing, but the cable will perform its functions properly.

Heat-shrink tubing

Then, in short-term approaches, heat it up with a lighter until it wraps around the wire as tightly as possible. Attention! Do not overheat the wire, otherwise you risk getting even more insulation problems.

Cable repair

You can fix the wire from charging the iPhone quickly and with your own hands in 3 main ways: using electrical tape, “heat shrink” and by soldering.

How to Fix iPhone Wire: Three Easy Ways

Apple manufactures iPhone wires from environmentally friendly materials, which, however, are rather impractical: they break, tear, and quickly fail. In this regard, the owners of “apple” phones often have the question of how to fix the wire from Aion yourself without the help of service center specialists.

Prevention measures

In order not to waste time, nerves and money on repairing the wire from the iPhone, it is better to try to prevent a breakdown with the help of improvised means. So, you can use a simple spring from a ballpoint pen. it will play the role of a shock absorber against dangerous cable deformations.

How to Fix Broken iPhone Charging Cable [ Unbelievable Hack ]

Take the spring and start winding it around the cable so that it is inside. Then fasten it to the bulge near the connector so that it does not fall off.

This solution does not look very aesthetically pleasing, but the probability of breaking and tearing the cable drops several times.

The listed methods are the best that can be done to fix the iPhone charging cable. It is worth remembering that careful use of wires will help to delay or completely eliminate their repair.

Lightning cable replacement

We do not recommend repairing the cord yourself, because by your actions, without the proper knowledge base, you can only worsen the situation and you will be forced to seek help from the service center. If you still aim to do this, here are detailed instructions for replacing the Iphone wire:

  • First you need to do the “disassembly” of the cable. Cut through the case, peel off the insulation and carefully disassemble the lightning itself. Do not throw away the plastic, it will still come in handy.
  • Remove metal parts from the device, remove the silicone from its surface.
  • Inside the plug, you must find the microcircuit and remove the glue from it with extreme care.
  • Next, you should tin the contacts with solder.
  • When we have coped with the solder, you can proceed to the pinout. We recommend that you find detailed instructions on how to carry out the pinout on the Internet.
  • Now you can start sequential assembly of the cable, having checked it in advance for operability.
READ  One earpiece from iPhone stopped working

If you have avoided short circuits and other amateur radio problems, you can enjoy the correct operation of a device that you have repaired with your own hands.

How to fix iPhone charging wire

Heat-shrink tubing

Put the heat shrink on the wire and place over the damaged area

Then, in short-term approaches, heat it with a lighter until it wraps around the wire as tightly as possible. Attention! Do not overheat the wire, otherwise you risk getting even more insulation problems.

Depending on the shrinkage coefficient, the tubes can decrease in diameter from 2 to 6 times

  • How to repair Apple device cable?
  • Life hack
  • Lightning cable replacement
  • Purchase upgrades
  • Useful Tips
  • Video

Of course, Apple has always been distinguished by the high cost of its equipment on the market and the poor quality of its cables. Chinese replica wires from Apple are of even poorer quality, and sometimes can be dangerous for users of mobile devices. Yes, and replacement with repair will cost a pretty penny, so today we will tell you about how to fix the iPhone 5s charging wire if it breaks.

How to Fix iPhone Wire: Three Easy Ways

Apple manufactures iPhone wires from environmentally friendly materials, which, however, are rather impractical: they break, tear, and quickly fail. In this regard, the owners of “apple” phones often have the question of how to fix the wire from Aion yourself without the help of service center specialists.

Life hack

Still puzzled by the question of how to fix the iPhone 5 cord? We will answer your question with one more repair method. You only need an iron spring, the diameter of which allows you to put it on the wire.

Important! Such springs can be found by disassembling a Chinese lighter or a non-working clock.

Let’s go to the very bottom: take the spring and thread it along the cable exactly in the place where the defect was found.

Important! This method is relevant only for those cases if the damage consists in a violation of the integrity of the cable insulation.

If everything is clear with insulation, then with the replacement of a lightning cable, things are more complicated.

How to repair Apple device cable?

Broke the cord from your phone’s charger, what should I do? Do not rush to contact a service center or choose a new one. Sometimes the situation can be saved with the help of scrap materials and your own hands.

And here is the method itself how to fix the cord from the iPhone 5 and another version:

  • We cut a piece of tube with the required dimensions.
  • Then we carefully put the “component” on the connector of the device and simply fix it with our own efforts or with the help of electrical tape.
  • Now you need to warm up the resulting structure over the hob burner, lighter or low-power gas burner.

Important! Do not use extremely high temperatures for processing and do not hold the wire over an open flame. Use hot air that rises above the flame.

How to repair Apple device cable?

Broke the cord from your phone’s charger, what should I do? Do not rush to contact a service center or choose a new one. Sometimes the situation can be saved with the help of improvised materials and your own hands.

And here is the method itself how to fix the cord from the iPhone 5 and another version:

  • We cut a piece of tube with the required dimensions.
  • Then we carefully put the “component” on the connector of the device and simply fix it with our own efforts or with the help of electrical tape.
  • Now you need to heat the resulting structure over the hob burner, lighter or low-power gas burner.

Important! Do not use extremely high temperatures for processing and do not hold the wire over an open flame. Use hot air that rises above the flame.

Lightning cable replacement

We do not recommend repairing the cord yourself, because by your actions, without the proper knowledge base, you can only worsen the situation and you will be forced to seek help from the service center. If you are still aiming to do this, here are detailed instructions for replacing the Iphone wire:

  • First you need to do the “disassembly” of the cable. Cut through the case, peel off the insulation and carefully disassemble the lightning itself. Do not throw away the plastic, it will still come in handy.
  • Remove metal parts from the device, remove the silicone from its surface.
  • Inside the plug, you must find the microcircuit and remove the glue from it with extreme care.
  • Next, you should tin the contacts with solder.
  • When we have coped with the solder, you can proceed to the pinout. We recommend that you find detailed instructions on how to carry out the pinout on the Internet.
  • Now you can start sequential assembly of the cable, having checked it in advance for operability.

If you have avoided short circuits and other amateur radio problems, you can enjoy the correct operation of a device that you have repaired with your own hands.

Useful Tips

By following such instructions, you will save yourself from the need for untimely replacement of the device and will be able to operate it for more than one year. But if you purchased a cable, but you don’t really want to deal with its protection, you can follow the following tips:

READ  How to reset iPhone 6 to factory settings

Purchase upgrades

There are special plastic “covers” for wires, which are put on those places of the wiring that suffer the most during operation. In other words. these devices will help to protect the cord from breakage in places of its bends.

Of course, Apple has always been distinguished by the high cost of its equipment on the market and the poor quality of its cables. Chinese replica wires from Apple are of even poorer quality, and sometimes can be dangerous for users of mobile devices. And replacement with repair will cost a pretty penny, so today we will tell you about how to fix the wire from charging iPhone 5s if it breaks.

Life hack

Still puzzled by the question of how to fix the iPhone 5 cord to charge your phone? We will answer your question with one more repair method. You only need an iron spring, the diameter of which allows you to put it on the wire.

Important! Such springs can be found by disassembling a Chinese lighter or a non-working clock.

Let’s go to the very bottom: take the spring and thread it along the cable exactly in the place where the defect was found.

Important! This method is relevant only for those cases if the damage consists in a violation of the integrity of the cable insulation.

If everything is clear with insulation, then with the replacement of a lightning cable, things are more complicated.

Lightning cable replacement

We do not recommend repairing the cord yourself, because by your actions, without the proper knowledge base, you can only worsen the situation and you will be forced to seek help from the service center. If you still aim to do this, here are detailed instructions for replacing the Iphone wire:

  • First you need to do the “disassembly” of the cable. Cut through the case, peel off the insulation and carefully disassemble the lightning itself. Do not throw away the plastic, it will still come in handy.
  • Remove metal parts from the device, remove the silicone from its surface.
  • Inside the plug, you must find the microcircuit and remove the glue from it with extreme care.
  • Next, you should tin the contacts with solder.
  • When we have coped with the solder, you can proceed to the pinout. We recommend that you find detailed instructions on how to carry out the pinout on the Internet.
  • Now you can start sequential assembly of the cable, having checked it in advance for operability.

If you have avoided short circuits and other amateur radio problems, you can enjoy the correct operation of a device that you have repaired with your own hands.

Purchase upgrades

There are special plastic “covers” for wires, which are put on those places of the wiring that suffer the most during operation. In other words, these devices will help to protect the cord from breakage in places of its bends.

Life hack

Still puzzled by the question of how to fix the iPhone 5 cord? We will answer your question with one more repair method. You only need an iron spring, the diameter of which allows you to put it on the wire.

Important! Such springs can be found by disassembling a Chinese lighter or a non-working clock.

Fix iPhone not charging. Repair Lightning cable not Charging

Let’s go to the very bottom: take the spring and thread it along the cable exactly in the place where the defect was found.

Important! This method is relevant only for those cases if the damage consists in a violation of the integrity of the cable insulation.

If everything is clear with insulation, then with the replacement of a lightning cable, things are more complicated.

How to fix iPhone charging wire?

Of course, Apple has always been distinguished by the high cost of its equipment on the market and the poor quality of its cables. Chinese replica wires from Apple are of even poorer quality, and sometimes can be dangerous for users of mobile devices. Yes, and replacement with repair will cost a pretty penny, so today we will tell you about how to fix the wire from the iPhone charging.

How to repair Apple device cable?

Broke your phone charger cord? Do not rush to contact a service center or choose a new one. Sometimes the situation can be saved with the help of improvised materials and your own hands.

And here is the method itself how to fix the cord from the iPhone 5 and another version:

  • We cut a piece of tube with the required dimensions.
  • Then we carefully put the “component” on the connector of the device and simply fix it with our own efforts or with the help of electrical tape.
  • Now you need to heat the resulting structure over the hob burner, lighter or low-power gas burner.

Important! Do not use extremely high temperatures for processing and do not hold the wire over an open flame. Use hot air that rises above the flame.

Useful Tips

By following such instructions, you will save yourself from the need for untimely replacement of the device and will be able to operate it for more than one year. But if you purchased a cable, but you don’t really want to deal with its protection, you can follow the following tips:

| Contacts | Content | RSS