How To Turn On The Speakers On The Monitor

1. Determine the polarity of the speaker terminals. Polarity is often indicated by the width of the terminals on the speakers: wide terminal. minus, close. plus. Also, the polarity of the Terminals is occasionally indicated by the signs “plus” and “minus”. If the terminals are identical and there is no sign marking, determine the polarity of connecting the speakers with the support of a battery with a voltage of 1.5 Volts. To do this, connect it to the speaker terminals. If the speaker cone moves forward (outward), the polarity of the Terminals corresponds to the polarity of the connected battery; if it is pushed into the speaker (back), the polarity of the terminals is opposite to the polarity of the battery totals.

2. Modern car radios have four independent power amplifiers (4 channels). The totals of THESE amplifiers have precise symbolic and color coding: each pair of totals has its own color. The negative outcome, as usual, is indicated by the leadership with a black stripe. We also determine the polarity and affiliation of the totals to any channel by special stickers on them. On THESE labels, the totals are indicated as “minus left front”, which means that this is a negative sum of the left front speaker. Often a sticker with additional color marking is located on the top panel of the car radio.

3. When connecting the speakers to the radio, use special wires with a cross section of at least 1.5 square millimeters. They often have a special color coding for the entire wire. As usual, the marking consists of a pair of “cold” (blue, black, green) and “hot” (scarlet, white, yellow) colors. Connect the speakers to the connecting wires and carefully insulate their terminals with electrical tape. Then connect the wires to the total of the car radio. Scrupulously insulate both correct and negative results from the radio amplifier.

4. Then connect the black (negative or general) total of the radio tape recorder to the car body. Connect the scarlet wire (plus power) last. Wire cross-section must be NOT less than 2.5 square millimeters.

A monitor with built-in speakers has a low sound quality, but it saves space on the table and frees up one outlet in an extension cord. A sound signal to such a monitor is supplied through a separate cable.

How To Turn On The Speakers On The Monitor

1. If your phone has two loudspeakers. one for conversational and the other for playing system sounds. find the speakerphone on in the call menu. This is only relevant if only one of the speakers is faulty. Usually, the speakerphone menu is located in the context menu of the call mode, but here everything depends more closely on the settings.

2. Use the headset that comes with many mobile devices. Connect it to the Corresponding jack of your mobile phone and select the Corresponding connection mode. If you have a wireless Bluetooth headset, enable communication on both devices and find the required model name by phone.

3. make a connection by holding the connect button on your headset, in the options for connecting devices in the phone, select “Audio devices”. To make calls, you will have to be continuously within the Bluetooth range.

4. Set your car audio system as a bluetooth headset. This is true if your receiver has a wireless function. Pairing also takes place in the mode of connecting audio devices.

5. Using this type of pairing, you can also not only make loud using the car speaker, but also use the player of your mobile device. Also, the phone is allowed to be connected via an audio cable if it has a connector for connection.

6. There are quite a few options for using a phone with a broken speaker, only in those that have wireless connection functions with devices, but do not forget about their impact on your health and DO NOT use them often. Also, when using a Bluetooth headset, be prepared for the fact that the phone battery will discharge much more rapidly than usual.

Helpful advice
DO NOT try to repair your phone speaker by yourself.

During the installation and connection of a new car radio or new speakers, a number of questions may appear: how to positively determine the polarity of the speaker, how to lay the wire, what is the polarity at the output of the car radio, which wires should be used to connect the speakers to the car radio. Knowing the results for such questions will help to avoid the most common mistakes when installing and connecting new devices.

you will need

  • – multimeter;
  • – battery with a voltage of 1.5 volts;
  • – connecting wire;
  • – insulating tape.

How to turn on speakers on benq monitor

How to turn on the speakers on the monitor?

Monitors can be equipped with built-in speakers. But for better sound quality, many people connect external speakers, constantly using which, you can face a very common problem when, when you turn them off, the sound from the monitor speakers (i.e. built-in) does not go. In order for the sound to appear, it is necessary to perform some actions.

The absence of sound after the performed manipulations may mean that the sound is simply turned off. To turn it on, find the speaker icon on the monitor panel. After clicking on this icon, you will see information about whether the speakers are on or off. If the displayed speaker image is crossed out with a red line, then the speakers on the monitor are turned off. Press the button below the speaker icon on the monitor panel to wake up your speakers. The disappearance of the red line in the picture will mean that you have completed the task.

If the sound does not appear after all the described actions, then you need to change some settings. This can be done by going to the Start menu in the Control Panel. In the window that opens, select the “Sound” item. In the “Playback” panel that appears, select “Properties” and then the “Levels” tab. If you find information when the speakers are off, make your adjustments. Now you can adjust the volume level and enjoy the sound.

If there is still sound, it is likely that the input on the block is selected incorrectly. Try to include any sound file and change the inputs on the system unit. A sound will indicate that the input is selected correctly.

Let’s say a monitor with a built-in speaker will not captivate your soul with its charming sound and richness of timbres, but it will save one outlet and space on the table. The speakers themselves will not turn on, therefore you have to take the wire and stretch it to the system unit.

1. Note that the cable that carries the image signals from the card (VGA or DVI) to the monitor does not contain audio wires. For this, an isolated thin cord is applied. It can be built into the monitor, but more often it is removable.

2. De-energize both the computer and the monitor before making any connections. If the audio cable is built-in, easily connect it to the green jack on your sound card. If it is detached, find it in the monitor package. If the last one jack of the standard Jack, similar to that installed on the sound card, the cord must be equipped with two identical plugs. Connect one of them (no matter which one) to the sound card as described above, and the second to the Audio In monitor jack. If your monitor has two RCA jacks, connect the red plug on the cable to the same colored jack on the monitor. Do the same with the white plug, and the green plug Connect to the sound card.

3. Upon receipt of a previously used monitor, the cable may not be included in the package. Then it should be collected. If it must have Jack-type plugs on both sides, it is easy to connect the same-named contacts of 2 such plugs with a cable of the required length. If on one side there should be one Jack type plug, and on the other. two RCA types, connect the common wires of all plugs together, the middle contact of the Jack plug Connect to the signal contact of the white RCA plug, and the far one to the signal contact of the red RCA plug.

4. Turn on the monitor and computer, make sure the speakers are now sounding. If this is not the case, adjust the volume using the computer’s software mixer (its name depends on the OS) and the volume knob or buttons on the monitor. If necessary, Exit the monitor from the Mute mode. If there is a separate Jack on its front panel, it is allowed to plug in headphones, while the built-in speakers will be disabled.

All sound on a TV set when connecting a computer via HDMI

The HDMI standard allows you to effortlessly display image and sound from a laptop or computer to an external monitor, in other words, a TV. To convey the picture and sound, it is enough to connect the computer to the device via a cable. However, just like with any other standard of data transfer, obstacles occur with HDMI, including due to incorrect OS options. One of the most common mistakes users have to deal with is the lack of sound on the TV set when a computer is connected to it via HDMI. This problem can be corrected by Several methods, the presence of which will be discussed below.

READ  Monitor Out Of Range How To Fix Windows 10

Be careful: Before proceeding with the tips below, make sure that the lack of sound on the TV when the computer is connected to it via HDMI is NOT due to the option of the TV itself. Often the reason is quite ordinary. the sound of the TV is reduced to zero or the “Silence Mode” (Mute) is turned on.

1. The set with the monitor must have at least 3 cords: power, (DVI or VGA), audio (mini jack 3.5mm). The connectors on THESE cords are so different that they can be easily confused (if you managed to push the VGA cable into the audio jack, then you have broken the motherboard). It turns out, take a wire with a mini jack plug. It is usually green at the end and matches the color of the audio input on the motherboard or audio card. If you were cheated and NOT provided with a cord. purchase it. Mini-jack father-father 3.5 mm. costs minimal, serves perfectly. Combine two slots: on the monitor and the system unit, and perform the next step.

2. All combined, but there is sound. There is no need to be sad, for example, you primitively did not turn it on, namely, did not press the on button. Look observant, it should be on the monitor panel, and above it is the audio speaker icon. Click on it, a picture of a crossed out or NOT crossed out speaker will appear on the screen. Be smart about what this can mean (probably crossed out. there is a sound, not crossed out. there is a sound), act according to logic.

3. combined, turned on, but there is sound. Wait for it to fall into a rage, curb your ardor and go to the operating system’s sound settings menu. In Windows, this is allowed through the Start menu. Control Panel. Sound. Playback tab. Properties. in a new window, the Tiers tab. It is allowed to go through the tray icon with the same speaker icon. Let’s say there is a treacherous checkmark on the off item somewhere. Remove it if so. Adjust the volume level in the program (and, if available, the corresponding buttons on the monitor).

4. If there is sound again. look at point one, let’s say you confused the input on the system unit. Turn on a sound file, say MP3, and change the inputs until you hear a sound.

If your phone speaker is broken and you need to make an urgent speaker, use other devices to replace the speaker. The choice in this case is limited by the configuration of your mobile phone.

1. Check if there is a 2nd cable connecting the monitor audio input to the computer sound card output. If it is, but there is still sound, first try to find the button with the crossed out speaker on the front panel of the monitor. Click on it, then either the LED above it will go out, or the speaker designation will also appear on the screen, but not crossed out. This indicates that the sound is now on. Pressing the button again will turn on the diode or the origin of the designation of the crossed out speaker. the sound is muted. Some monitors have a separate button for metamorphosis of the speaker operating mode. this function can be turned on and off via the menu.

2. If the monitor is taken out of the mute mode, but you still cannot hear anything, detect the volume control. Even on monitors, where all adjustments are made electronically, such a regulator can be analog. Turn the knob and the sound should appear. If the knob is missing, look on the front panel for the arrow buttons, between which the speaker designation is located, or Try to find the item to adjust the volume in the monitor menu.

3. It is impossible to exclude the wrong setting of the operating system mixer. but then there will be no sound even if ordinary speakers are connected to the sound card. Run the corresponding program (its name depends on which OS is used) and check if the audio output is disabled.

4. Even if there is a cable, it is not a fact that it is positively connected. Check if it is connected with one plug to the green jack of the sound card, and by the other to the monitor jack marked as Audio in. Reposition it into the corresponding slots if necessary. In addition, the cord may be defective. To find out if this is so, disconnect it from both the computer and the monitor, and ring with an ohmmeter.

5. If you do not have a cable, look for it in the package box of your monitor. If He is not found there, make it yourself. Take two 3.5mm Stereo Reference Jack (TRS) plugs. Use a three-wire cord to combine their contacts of the same name.

note!
All switching is carried out with de-energized equipment.

Some monitors, both liquid crystal and tube, are equipped with built-in speakers. Similar to separate speakers, the built-in can be connected to the computer sound card with a stereo cable.

Selecting the correct playback device

When an external information output device is connected to a computer via HDMI. a TV or a monitor, the operating system should automatically find that the sound will be broadcast through the connected source by default. If this, for one reason or another, did not work out, the user must, without the help of others, assign the TV to play sound as a device. For this purpose, you

  • In the lower right corner of the screen, you need to click on the speaker icon (“Digital Audio”) with the right mouse button and in the Fav window that opens “Playback devices”;
  • A window with options for playback devices will open, in which you need a Favorite TV (or another device from which sound should be output) and press it with the right mouse button. In the pop-up menu, click Set as default;

1. Check if there is a 2nd cable connecting the monitor audio input to the computer sound card output. If it is, but there is still sound, first try to find the button with the crossed out speaker on the front panel of the monitor. Click on it, then either the LED above it will go out, or the speaker designation will also appear on the screen, but not crossed out. This indicates that the sound is now on. Pressing the button again will turn on the diode or the origin of the designation of the crossed out speaker. the sound is muted. Some monitors have a separate button for metamorphosis of the speaker operating mode. this function can be turned on and off via the menu.

2. If the monitor is taken out of the mute mode, but you still cannot hear anything, detect the volume control. Even on monitors, where all adjustments are made electronically, such a regulator can be analog. Turn the knob and the sound should appear. If the knob is missing, look on the front panel for the arrow buttons, between which the speaker designation is located, or Try to find the item to adjust the volume in the monitor menu.

3. It is impossible to exclude the wrong setting of the mixer of the operating system. but then there will be no sound even if ordinary speakers are connected to the sound card. Run the corresponding program (its name depends on which OS is used) and check if the audio output is disabled.

4. Even if there is a cable, it is not a fact that it is positively connected. Check if it is connected with one plug to the green jack of the sound card, and by the other to the monitor jack marked as Audio in. Reposition it into the corresponding slots if necessary. In addition, the cord may be defective. To find out if this is so, disconnect it from both the computer and the monitor, and ring with an ohmmeter.

5. If you do not have a cable, look for one in the package box of your monitor. If He is not found there, make it yourself. Take two 3.5mm Stereo Reference Jack (TRS) plugs. Use a three-wire cord to combine their contacts of the same name.

Note! All switching is carried out with de-energized equipment.

Some monitors, both liquid crystal and tube, are equipped with built-in speakers. Similar to separate speakers, the built-in can be connected to the computer sound card with a stereo cable.

instruction

1. If your phone has two loudspeakers. one for conversational and the other for playing system sounds. find the speakerphone on in the call menu. This is only relevant if only one of the speakers is faulty. Usually, the speakerphone menu is located in the context menu of the call mode, but here everything depends more closely on the settings.

2. Use the headset that comes with many mobile devices. Connect it to the Corresponding jack of your mobile phone and select the Corresponding connection mode. If you have a wireless Bluetooth headset, enable communication on both devices and find the required model name by phone.

3. make a connection by holding the connect button on your headset, in the options for connecting devices in the phone, select “Audio devices”. To make calls, you will have to be continuously within the Bluetooth range.

4. Set your car audio system as a bluetooth headset. This is true if your receiver has a wireless function. Pairing also takes place in the mode of connecting audio devices.

READ  Take A Photo To The Home Screen

5. Using this type of pairing, you can also not only make loud using the car speaker, but also use the player of your mobile device. Also, the phone is allowed to be connected via an audio cable if it has a connector for connection.

6. There are quite a few options for using a phone with a broken speaker, only in those that have wireless connection functions with devices, but do not forget about their impact on your health and DO NOT use them often. Also, when using a Bluetooth headset, be prepared for the fact that the phone battery will discharge much more rapidly than usual.

Helpful Hint DO NOT try to repair your phone speaker by yourself.

During the installation and connection of a new car radio or new speakers, a number of questions may appear: how to positively determine the polarity of the speaker, how to lay the wire, what is the polarity at the output of the car radio, which wires should be used to connect the speakers to the car radio. Knowing the results for such questions will help to avoid the most common mistakes when installing and connecting new devices.

  • – multimeter;
  • – battery with a voltage of 1.5 volts;
  • – connecting wire;
  • – insulating tape.

1. The set with the monitor must have at least 3 cords: power, (DVI or VGA), audio (mini jack 3.5mm). The connectors on THESE cords are so different that they can be easily confused (if you managed to push the VGA cable into the audio jack, then you have broken the motherboard). It turns out, take a wire with a mini jack plug. It is usually green at the end and matches the color of the audio input on the motherboard or audio card. If you were cheated and NOT provided with a cord. purchase it. Mini-jack father-father 3.5 mm. costs minimal, serves perfectly. Combine two slots: on the monitor and the system unit, and perform the next step.

2. All combined, but there is sound. There is no need to be sad, for example, you primitively did not turn it on, namely, did not press the on button. Look observant, it should be on the monitor panel, and above it is the audio speaker icon. Click on it, a picture of a crossed out or NOT crossed out speaker will appear on the screen. Be smart about what this can mean (probably crossed out. there is a sound, not crossed out. there is a sound), act according to logic.

3. combined, turned on, but there is sound. Wait for it to fall into a rage, curb your ardor and go to the operating system’s sound settings menu. In Windows, this is allowed through the Start menu. Control Panel. Sound. Playback tab. Properties. in a new window, the Tiers tab. It is allowed to go through the tray icon with the same speaker icon. Let’s say there is a treacherous checkmark on the off item somewhere. Remove it if so. Adjust the volume level in the program (and, if available, the corresponding buttons on the monitor).

4. If there is sound again. look at point one, let’s say you confused the input on the system unit. Turn on a sound file, say MP3, and change the inputs until you hear a sound.

If your phone speaker is broken and you need to make an urgent speaker, use other devices to replace the speaker. The choice in this case is limited by the configuration of your mobile phone.

How to turn on the speakers on the monitor

Let’s say a monitor with a built-in speaker will not captivate your soul with its charming sound and richness of timbres, but it will save one outlet and space on the table. The speakers themselves will not turn on, therefore you have to take the wire and stretch it to the system unit.

1. Note that the cable that carries the image signals from the card (VGA or DVI) to the monitor does not contain audio wires. For this, an isolated thin cord is applied. It can be built into the monitor, but more often it is removable.

2. De-energize both the computer and the monitor before making any connections. If the audio cable is built-in, easily connect it to the green jack on your sound card. If it is detached, find it in the monitor package. If the last one jack of the standard Jack, similar to that installed on the sound card, the cord must be equipped with two identical plugs. Connect one of them (no matter which one) to the sound card as described above, and the second to the Audio In monitor jack. If your monitor has two RCA jacks, connect the red plug on the cable to the same colored jack on the monitor. Do the same with the white plug, and the green plug Connect to the sound card.

3. Upon receipt of a previously used monitor, the cable may not be included in the package. Then it should be collected. If it must have Jack-type plugs on both sides, it is easy to connect the same-named contacts of 2 such plugs with a cable of the required length. If on one side there should be one Jack type plug, and on the other. two RCA types, connect the common wires of all plugs together, the middle contact of the Jack plug Connect to the signal contact of the white RCA plug, and the far one to the signal contact of the red RCA plug.

4. Turn on the monitor and computer, make sure the speakers are now sounding. If this is not the case, adjust the volume using the computer’s software mixer (its name depends on the OS) and the volume knob or buttons on the monitor. If necessary, Exit the monitor from the Mute mode. If there is a separate Jack on its front panel, it is allowed to plug in headphones, while the built-in speakers will be disabled.

How do I turn on the speakers on the monitor? How to turn on the speakers on the monitor. How to turn on the sound on the monitor?

A monitor with built-in speakers has a low sound quality, but it saves space on the table and frees up one outlet in the extension cord. A sound signal is supplied to such a monitor through a separate cable.

How to combine speakers

During the installation and connection of a new car radio or new speakers, a number of questions may appear: how to positively determine the polarity of the speaker, how to lay the wire, what is the polarity at the output of the car radio, which wires should be used to connect the speakers to the car radio. Knowing the results for such questions will help to avoid the most common mistakes when installing and connecting new devices.

you will need

  • – multimeter;
  • – battery with a voltage of 1.5 volts;
  • – connecting wire;
  • – insulating tape.

How to turn on the speakers on the monitor

Some monitors, both liquid crystal and tube, are equipped with built-in speakers. Similar to separate speakers, the built-in can be connected to the computer sound card with a stereo cable.

1. The set with the monitor must have at least 3 cords: power, (DVI or VGA), audio (mini jack 3.5mm). The connectors on THESE cords are so different that they can be easily confused (if you managed to push the VGA cable into the audio jack, then you have broken the motherboard). It turns out, take a wire with a mini jack plug. It is usually green at the end and matches the color of the audio input on the motherboard or audio card. If you were cheated and NOT provided with a cord. purchase it. Mini-jack father-father 3.5 mm. costs minimal, serves perfectly. Combine two slots: on the monitor and the system unit, and perform the next step.

2. All combined, but there is sound. There is no need to be sad, for example, you primitively did not turn it on, namely, did not press the on button. Look observant, it should be on the monitor panel, and above it is the audio speaker icon. Click on it, a picture of a crossed out or NOT crossed out speaker will appear on the screen. Be smart about what this can mean (probably crossed out. there is a sound, not crossed out. there is a sound), act according to logic.

3. combined, turned on, but there is sound. Wait for it to fall into a rage, curb your ardor and go to the operating system’s sound settings menu. In Windows, this is allowed through the Start menu. Control Panel. Sound. Playback tab. Properties. in a new window, the Tiers tab. It is allowed to go through the tray icon with the same speaker icon. Let’s say there is a treacherous checkmark on the off item somewhere. Remove it if so. Adjust the volume level in the program (and, if available, the corresponding buttons on the monitor).

4. If there is sound again. look at point one, let’s say you confused the input on the system unit. Turn on a sound file, say MP3, and change the inputs until you hear a sound.

How to turn on sound without speakers

If your phone speaker is broken and you need to make an urgent speaker, use other devices to replace the speaker. The choice in this case is limited by the configuration of your mobile phone.

you will need

1. Check if there is a 2nd cable connecting the monitor audio input to the computer sound card output. If it is, but there is still sound, first try to find the button with the crossed out speaker on the front panel of the monitor. Click on it, then either the LED above it will go out, or the speaker designation will also appear on the screen, but not crossed out. This indicates that the sound is now on. Pressing the button again will turn on the diode or the origin of the designation of the crossed out speaker. the sound is muted. Some monitors have a separate button for metamorphosis of the speaker operating mode. this function can be turned on and off via the menu.

READ  How To Record Screen With Voice

2. If the monitor is taken out of the mute mode, but you still cannot hear anything, detect the volume control. Even on monitors, where all adjustments are made electronically, such a regulator can be analog. Turn the knob and the sound should appear. If the knob is missing, look on the front panel for the arrow buttons, between which the speaker designation is located, or Try to find the item to adjust the volume in the monitor menu.

3. It is impossible to exclude the wrong setting of the mixer of the operating system. but then there will be no sound even if ordinary speakers are connected to the sound card. Run the corresponding program (its name depends on which OS is used) and check if the audio output is disabled.

4. Even if there is a cable, it is not a fact that it is positively connected. Check if it is connected with one plug to the green jack of the sound card, and by the other to the monitor jack marked as Audio in. Reposition it into the corresponding slots if necessary. In addition, the cord may be defective. To find out if this is so, disconnect it from both the computer and the monitor, and ring with an ohmmeter.

5. If you do not have a cable, look for it in the package box of your monitor. If He is not found there, make it yourself. Take two 3.5mm Stereo Reference Jack (TRS) plugs. Use a three-wire cord to combine their contacts of the same name.

note!
All switching is carried out with de-energized equipment.

1. If your phone has two loudspeakers. one for conversational and the other for playing system sounds. find the speakerphone on in the call menu. This is only relevant if only one of the speakers is faulty. Usually, the speakerphone menu is located in the context menu of the call mode, but here everything depends more closely on the settings.

2. Use the headset that comes with many mobile devices. Connect it to the Corresponding jack of your mobile phone and select the Corresponding connection mode. If you have a wireless Bluetooth headset, enable communication on both devices and find the required model name by phone.

3. make a connection by holding the connect button on your headset, in the options for connecting devices in the phone, select “Audio devices”. To make calls, you will have to be continuously within the Bluetooth range.

4. Set your car audio system as a bluetooth headset. This is true if your receiver has a wireless function. Pairing also takes place in the mode of connecting audio devices.

5. Using this type of pairing, you can also not only make loud using the car speaker, but also use the player of your mobile device. Also, the phone is allowed to be connected via an audio cable if it has a connector for connection.

6. There are quite a few options for using a phone with a broken speaker, only in those that have wireless connection functions with devices, but do not forget about their impact on your health and DO NOT use them often. Also, when using a Bluetooth headset, be prepared for the fact that the phone battery will discharge much more rapidly than usual.

on this topic

Helpful advice
DO NOT try to repair your phone speaker by yourself.

How to turn on the sound on the monitor

A monitor with built-in speakers has a low sound quality, but it saves space on the table and frees up one outlet in an extension cord. A sound signal to such a monitor is supplied through a separate cable.

How to turn on the speakers on the monitor

Let’s say a monitor with a built-in speaker will not captivate your soul with its charming sound and richness of timbres, but it will save one outlet and space on the table. The speakers themselves will not turn on, therefore you have to take the wire and stretch it to the system unit.

1. Determine the polarity of the speaker terminals. Polarity is often indicated by the width of the terminals on the speakers: wide terminal. minus, close. plus. Also, the polarity of the Terminals is occasionally indicated by the signs “plus” and “minus”. If the terminals are identical and there is no sign marking, determine the polarity of connecting the speakers with the support of a battery with a voltage of 1.5 Volts. To do this, connect it to the speaker terminals. If the speaker cone moves forward (outward), the polarity of the Terminals corresponds to the polarity of the connected battery; if it is pushed into the speaker (back), the polarity of the terminals is opposite to the polarity of the battery totals.

2. Modern car radios have four independent power amplifiers (4 channels). The totals of THESE amplifiers have precise symbolic and color coding: each pair of totals has its own color. The negative outcome, as usual, is indicated by the leadership with a black stripe. We also determine the polarity and affiliation of the totals to any channel by special stickers on them. On THESE labels, the totals are indicated as “minus left front”, which means that this is a negative sum of the left front speaker. Often a sticker with additional color marking is located on the top panel of the car radio.

3. When connecting the speakers to the radio, use special wires with a cross section of at least 1.5 square millimeters. They often have a special color coding for the entire wire. As usual, the marking consists of a pair of “cold” (blue, black, green) and “hot” (scarlet, white, yellow) colors. Connect the speakers to the connecting wires and carefully insulate their terminals with electrical tape. Then connect the wires to the total of the car radio. Scrupulously insulate both correct and negative results from the radio amplifier.

4. Then connect the black (negative or general) total of the radio tape recorder to the car body. Connect the scarlet wire (plus power) last. Wire cross-section must be NOT less than 2.5 square millimeters.

task bar

In this case, you can activate the laptop speakers in just 2 clicks:

  • Left-click on the Corresponding icon in the taskbar.
  • Turn on the speakers with one more click.
  • Yes, it’s that simple. Difficulties in this case will NOT arise even for beginners.

Function keys

Using function keys, users can quickly turn on the touchpad on a laptop or put the device into airplane mode. To turn on the sound on Asus laptops, you must simultaneously press the Fn and F10 buttons on the keyboard.

Function Keys

You can also add volume using the function keys. As a rule, they are located next to the on / off sound button. To set the desired sound on Asus laptops, you need to press Fn and F11 (volume down) or Fn and F12 (volume up). In second-brand laptops, the buttons may be different. In any case, they will be marked with the appropriate icons. By the way, using the function keys, you can adjust the brightness on a laptop.

How to turn up the volume on a laptop?

There are many ways to make the sound loud and amplify the signal. over, you can even adjust the volume from the keyboard. The most popular options are as follows:

  • through the taskbar;
  • using function keys;
  • via windows options.

Each method has its own advantages and disadvantages. However, all of the following methods allow you to make the desired sound settings.

task bar

The technique is very simple. In fact, it almost completely copies the previously mentioned method of inclusion:

  • Click on the sound icon on the taskbar.
  • Set the mixer to the desired volume.
  • This method is not only simple, but also fast. Adjusting the sound volume through the taskbar is very quick.

How to turn on sound on a laptop?

There are several ways to turn on the sound and increase its volume on laptops running Windows:

  • through the taskbar;
  • using function keys.

Both methods are distinguished by their simplicity and speed. Of course, they will NOT be able to figure out why the sound on the computer does not work, but turning on the speakers will NOT be difficult.

How to set up sound on a laptop?

Many laptop and computer users often know how to turn on bluetooth or what to do if the keyboard does not work. However, sometimes more trivial tasks also cause difficulties. For example, people don’t know how to turn on the sound and turn up the volume. In fact, solving THESE tasks is very simple.

Windows options

This method is a little time consuming. To amplify the sound and make it louder, you need to perform the following manipulations:

  • Right-click on “Start” and select the “Options” option from the menu.
  • Open the subsection “Sound” and Set the mixer to the desired volume.
  • Raising the volume is somewhat more difficult in this case. However, you can adjust other sound settings in the Windows settings. The variability of the presented customization method is higher.

Summing up

It is very easy to turn on the sound on your laptop and increase its volume. All manipulations will take no more than a minute. You can even configure the settings you want using the keyboard. Naturally, making the sound very loud solely with the capabilities of the laptop speakers will not work. To do this, you need to “add” speakers and an amplifier to the laptop.

| Contacts | Content | RSS