iPhone 8 Screen Won’t Turn Off

What can cause the problem with iPhone

The reasons for iPhone breakdown can be software and hardware. In cases where the phone freezes or turns off, because incorrectly configured and buggy, most likely you can fix it on your own. At home, you can also disconnect and reconnect the battery if you have experience disassembling an iPhone and have tools: spudger, suction cup, tweezers.

If iPhone won’t turn on due to complex hardware problems, it’s best to contact a qualified technician right away. Visit an Apple Service Center if you suspect a manufacturing defect. And urgently seek help from the workshop if you spill liquid on the iPhone: tea, coffee, juice or other drink. You cannot dry the display with a hairdryer, you need to immediately carry the gadget to the master. It’s important to clean the pads and boards in time to prevent corrosion inside the iPhone.

Basically, problems with the iPhone (difficulties with turning on) arise for the following reasons:

  • The battery is completely discharged or was in the cold (in this case, you need to wait. the phone does not turn on only temporarily)
  • smartphone has been dropped, improperly repaired or flooded
  • a factory defect of parts is allowed (for example, a power controller, a U2 chip or a battery. the phone will not turn on without them)
  • software malfunction (iOS itself or other software)
  • using a charger that is broken (that is, the iPhone does not turn on, although it hangs on the charge, since it SIMply does not charge)

Find the cause of the breakdown, act consistently and you may not have to spend money on repairs.

How can you solve the problem with the iPhone without leaving home

First, make sure the battery is charged and not the cause. Connect iPhone to original charger and press “Power”. The device turns on quickly under normal conditions, but if the iPhone has not worked for a long time, then, most likely, the battery went into deep discharge mode and you need to wait about half an hour. Check if the charger is heating up, if there is any dirt in the connector. The iPhone may not start because there is not enough current (this happens when using cheap chargers and connecting the battery to the USB port of the computer).

If you see a black screen, and the phone buzzes and beeps intermittently but won’t turn on, try restarting it. ALGorithm:

  • press the “Sleep / Wake” and “Home” buttons at the same time (if you have an iPhone 7 or 7S, use a combination of “Power” and “Volume”)
  • hold (about 10-15 seconds) until the Apple logo loads

A hard reset will not erase iPhone data (contacts, pictures, videos, etc.). If the smartphone still does not turn on, you will have to act more radically:

  • connect the original USB cable to the computer and open iTunes
  • press the “Power” and “Volume” buttons (for 7th generation models) or “Power” and “Home” (for iPads, iPods, iPhones 6 and earlier); release them only when the screen goes blank
  • press Home and, connecting the USB cable to the smartphone, hold the button until the iTunes logo turns on and the plug icon appears
  • confirm the procedure for updating iOS (if you want to keep the data) or restoring iPhone (if the information has already been saved on another medium)

The installation process for new software takes about forty minutes. At this time, it will seem that the iPhone has turned off. the screen will turn off, the phone will not vibrate, buzz and get very hot. During the procedure, the Internet connection should work well, otherwise the software will not load.

iPhone won’t turn on

And get the best deals from trusted masters.

  • Compare and choose the best conditions
  • Feedback only from interested professionals
  • Do not waste time communicating with intermediaries

If the iPhone is disconnected, does not charge or turn on (for example, vibrates, shows the logo and turns off immediately), do not rush to go to the service and call the wizard. In some cases, problems with Apple equipment can be solved without qualified intervention. Perform diagnostics at home, try to understand why the smartphone turns off. Try to find the exact cause of the iPhone breakdown and fix it yourself.

IPhone Symptoms

Problems with an iPhone can manifest themselves in different ways, depending on the nature of the problem. Possible situations:

  • the screen is black or has gone out, the phone does not respond to button presses and touching the sensor
  • The iPhone turns on, but it gets very hot (you can feel a hot display or adapter) and quickly discharges (the battery lasts for several hours, even if the indicator is on, and the gadget hangs on charging all night)
  • the smartphone is charged, but you cannot turn it on. the logo flashes for a long time, iOS does not start
  • iPhone keeps shutting down spontaneously
  • iPhone won’t turn on, although it beeps and vibrates

If you have used an iPhone in the cold for a long time and cannot turn it on, the situation is normal, since the battery is designed only for a certain temperature. Wait for the battery to warm up to room temperature, and only then start diagnostics.

Software settings ok: what to do

If everything is in order with iOS, firmware and applications on the iPhone, contact the specialists.

Of course, with the right tools, you can disassemble the iPhone yourself and, for example, turn off and reconnect the battery. But without experience and qualifications, you can accidentally damage other parts and, of course, violate the warranty conditions.

Owners of iPhones with a valid warranty can contact the employees of an authorized service center to make repairs for free. If the warranty is violated (for example, the iPhone has survived drops in water or shocks that require replacement of the case), the best way to solve the problem is to call an experienced technician at home.

YouDo is a great alternative to free classified ads. Benefits of the service for iPhone owners:

  • performers provide only reliable data, undergo a special check (verification)
  • technicians quickly and accurately find the cause of the breakdown if the iPhone constantly turns off, does not respond to buttons or does not work at all
  • professionals provide on-site iPhone repair services, set reasonable and provide guarantees up to 1 year
  • private traders and companies use only original Apple spare parts (batteries, power controllers, etc.) and professional tools (allowing you to carefully disassemble the iPhone case, disconnect the battery, repair the motherboard)

Apply for youdo.com in a couple of clicks, select an artist and call him at any convenient time. Tell the phone technician all the details: why the iPhone turned off, how long the phone flashes or vibrates, whether you tried to disconnect the battery and restart the device, how much the charger heats up.

If the iPhone does not turn on due to faulty hardware, performer Yudu will fix the breakage within 1 hour.

Connect iPhone to iTunes in Recovery Mode

If the iPhone does not respond to either charging or hard restarting, the smartphone must be put into recovery mode. Here we immediately note that you may not need to directly restore the iPhone. Everything in order.

The first step is to try to get your iPhone back on track without restoring it. This method has saved thousands of iPhones without erasing data, which implies recovery. Therefore, we strongly recommend that you initially use it.

Connect your iPhone to your computer using a USB cable and launch iTunes (Finder window in macOS Catalina).

Enter iPhone into recovery mode. For this:

Note: iPhone must be connected to computer via USB cable.

  • On iPhone 6s, iPhone 6, iPhone 5s, and earlier. Press the Home and Power buttons (the power button, located on the side or top of the case) at the same time for about 20 seconds until the iTunes logo (laptop logo in iOS 13) appears on the screen.
  • On iPhone 7 and iPhone 7 Plus. Press and hold the Volume Down and Power (Side) buttons at the same time for about 20 seconds until the iTunes logo (laptop logo in iOS 13) appears.
  • On iPhone 8/8 Plus, iPhone X and newer. Press and immediately release the volume up button. Press and immediately release the volume down button. Then hold down the side button and hold it for about 20 seconds until the iTunes logo appears (laptop logo in iOS 13).

In the iTunes window, click “Eject iPhone”.

Restart your iPhone. To do this, SIMply hold down the Power button (side button). You can also perform a forced reboot using the method described above.

As a result of this operation, your iPhone can turn on and work again as before without the need to restore.

Perform a hard reboot

The first thing to do if the iPhone won’t turn on is to force it (aka “hard”) restart. It takes the iPhone out of recovery mode, which may have been accidentally turned on, and SIMply resets software errors on the device.

Force restarting works differently on different iPhone models.

On iPhone 6s, iPhone 6, iPhone 5s, and earlier. Press and hold the Home and Power buttons (Power button, located on the side or top of the case) at the same time for 15 seconds until the Apple logo appears on the screen.

On iPhone 7 and iPhone 7 Plus. Press and hold the Volume Down and Power (Side) buttons at the same time for 15 seconds until the Apple logo appears.

On iPhone 8/8 Plus, iPhone X and later. Press and immediately release the volume up button. Press and immediately release the volume down button. Then press and hold the side button for 15 seconds until the Apple logo appears.

? Remember how a forced reboot is performed on your device. It can help with most of these crashes that can happen on the iPhone.

A forced reboot is completely safe. Its execution does not delete any data on the iPhone, so you can perform it safely.

❗ Methods to restore iPhone in this tutorial are arranged from easy to difficult. If a “hard” reboot doesn’t help, go to the next method. He will have to help solve the problem.

iPhone won’t turn on, black screen. what to do

IPhone won’t turn on? There is a solution.

iPhone won’t turn on and the apple is on? Or is the screen completely black and the iPhone is unresponsive to button presses? Both of these problems can happen to any iPhone user without dropping the smartphone. Learn what to do if your iPhone won’t turn on in this tutorial. You can solve the problem without going to the service center and the accompanying expenses.

READ  Blue screen when loading windows

Restore iPhone via iTunes

If the iPhone does not turn on even after connecting to the computer, then only restoration will help out.

❗ In most cases, recovery involves deleting all data from the device. You can return them only if you have an up-to-date backup.

Connect your iPhone to your computer using a USB cable and launch iTunes (Finder window in macOS Catalina).

Enter iPhone into recovery mode. For this:

Note: iPhone must be connected to computer via USB cable.

  • On iPhone 6s, iPhone 6, iPhone 5s, and earlier. Press the Home and Power buttons (the power button, located on the side or top of the case) at the same time for about 20 seconds until the iTunes logo (laptop logo in iOS 13) appears on the screen.
  • On iPhone 7 and iPhone 7 Plus. Press and hold the Volume Down and Power (Side) buttons at the same time for about 20 seconds until the iTunes logo (laptop logo in iOS 13) appears.
  • On iPhone 8/8 Plus, iPhone X and later. Press and immediately release the volume up button. Press and immediately release the volume down button. Then hold down the side button and hold it for about 20 seconds until the iTunes logo appears (laptop logo in iOS 13).

iTunes will report detecting iPhone in recovery mode. In the window that opens, select “Update”. Initially, you should choose this option, as it can allow you to return the device to a working state without losing data.

If data lossless recovery is possible, the iPhone update process will start. Wait for it to end. ❗ Never disconnect iPhone from your computer.

If the update fails, then a recovery should be performed. Re-enter iPhone into recovery mode (step # 2) and select “Recover” in the iTunes window that opens. Wait for the end of the operation.

Updating or restoring will return your iPhone to working condition.

Connect iPhone to charger

Often, the iPhone won’t turn on and show no signs of life due to the fact that its battery is dead. Connect your smartphone to the charger and leave it connected for an hour.

Here are some important tips to keep in mind:

  • Use original or quality charging accessories. There have been cases in which the iPhone turned off due to a dead battery, but did not charge due to using a broken charging adapter or cable. Be sure to check that the charger and cable are in working order.
  • Charge iPhone with electricity. It is very common for users to charge their iPhone from a computer USB port. But due to the old battery in the smartphone and the low power of the connector, charging SIMply does not occur.
  • Check if the connector is dirty. Sometimes iPhone won’t start charging due to a heavily soiled Lightning connector. Examine the charging port. If it is really dirty, clean it gently, for example with a toothpick.

⚡ How to understand that the iPhone started charging?

If the battery logo with the Lightning cable is on the screen. iPhone does not charge and asks to connect to a charger. If this logo is displayed after you put the iPhone on charge, then the cable or adapter is out of order. Use other charging accessories.

If only the battery is displayed on the screen, then charging is successful. It’s worth worrying only if this logo is displayed without changes for more than 30 minutes. In this case, you should also replace the charging adapter and cable.

If all else fails

None of the above methods helped? This means that your iPhone has a physical breakdown and you need to contact a service center.

Why iPhone won’t turn on?

A failed battery is the most common reason iPhone stops turning on. If you previously noticed that the smartphone was rapidly discharged, turned off by 10-30% of the charge, turned off in the cold and any other SIMilar anomalies happened to it, then the problem is definitely with the battery.

Replacement will help. expensive in Apple authorized service centers. 3000-7000 thousand rubles.

Broken power controller is another very common cause of iPhone failure. Symptoms before a smartphone fails are SIMilar to a battery breakdown. accidental device shutdowns, overheating.

Replacement is relatively inexpensive. You can change the power controller or other microcircuit associated with the charging process for about 2000 rubles.

Failure of other components. iPhone may not turn on due to the breakdown of dozens of different components, including the motherboard. Most often this happens after the fall of the smartphone. It is possible to determine what exactly broke down only during the diagnosis.

Renovations can be ruinous. If the iPhone didn’t overheat before it broke, then it’s best to start praying right away that the motherboard is intact. Replacing it, especially on newer iPhone models, will cost a pretty penny.

Before going to the service center, we recommend that you contact Apple official support. The company’s specialists will be happy to help with advice.

Using Force Restart to Enter DFU Mode

When the phone is not functioning, it is worth trying to enter DFU mode:

  • Connect the device to a computer with iTunes.
  • Open iTunes on your computer and click the button with the iPhone icon.
  • Press the volume up button on the smartphone.
  • Let her go quickly.
  • Repeat with volume down button.
  • Press the side button and hold until the smartphone turns off.
  • After the gadget turns off, press the side button and SIMultaneously the volume down button, and hold for five seconds.
  • Release only the side button. iTunes will display a message that the smartphone is being updated.

Easy reboot

If iPhone 8 is unresponsive or freezes, the following steps will help:

  • Press the volume up button and quickly release it.
  • Repeat action with volume down button.
  • Press and hold the side button until the Apple logo appears on the screen.

The phone should forcibly reboot and restore its previous work.

IPhone 8 freezes and does not restart, what to do, how to restart

reading time: 1 minute

New phone models, although reliable, are not immune to freezing. The causes of the problem may be different:

  • Mechanical damage;
  • Software errors;
  • Water ingress;
  • Failed settings;
  • Marriage.

If your iPhone 8 is frozen, the screen does not respond, and you do not know what to do, do not panic, but restart it. Some features in iPhone 8 are identical to older models, but the restart method has been changed.

Factory reset in iPhone 8

As a rule, phones freeze due to included or downloaded programs. Restart and shutdown methods are capable of restoring functions, but if the iphone 8 plus still won’t turn on, it’s best to reset all settings. Don’t forget to save your data. You can update a gadget in two ways.

Reset all settings. This method does not delete data from the phone. It is necessary:

  • Enter “Settings”.
  • Select “Basic”.
  • Then “Reset”.
  • Click “Reset all settings”.

Erase content and settings. This method erases all data from the device. For this you need:

  • Enter “Settings”.
  • Select “Basic”.
  • Next “Reset”.
  • Click on “Erase content and settings”.

If the iPhone 8 does not turn on, what you do not know to do, and the restart did not help, then you need to contact the service.

What to do if restarting doesn’t work

If your iPhone 8 won’t turn on or respond to charging, you need to try a different restart method:

  • Press and hold the Home and Side buttons at the same time.
  • Wait for the phone to turn off.
  • After a couple of minutes, press and hold the side button.
  • Wait until the logo appears.

If done correctly, the smartphone will return to normal operation.

Disconnect via Assistive Touch

If the keys do not work, the smartphone turns off via the sensor.

To do this, go to “Settings”. “General”. “Universal Access”. activate “Assistive Touch”. click on the button in the lower right corner. select “device” in the additional menu. click “LockScreen”. A slider will appear, after swipe, the smartphone will turn off.

Disconnection by buttons

To turn off iPhone X, you need to SIMultaneously hold down the shutdown button with one of the volume buttons. This “” or “-” has no special meaning. Hold the press for 3-4 seconds. A slider will appear, which must be swiped to the right. The device will fall asleep immediately.

How to turn off iPhone without a button

The keys can fail at just the right moment. They can hover, sink, or SIMply stop responding to pressure. In such a situation, you can turn off the iPhone without a button, but with a working sensor.

Standard way

Despite the fact that the Iphone 7 does not have a Home key, it can be turned off by pressing the Power key. It’s on the right side of the sidebar. Then a slider will appear on the screen, after activating it, the screen will be turned off.

How to turn off iPhone 6

The iPhone 6 looks a bit different from the iPhone 5 in terms of the location of the power button and size. It is located on the side panel, and not at the top, as it was before.

Standard way

To turn off iPhone 5, hold down the Power key at the top of the device. After 3-4 seconds, a window will appear on the screen that will require you to swipe to the right to disconnect. Turn on the smartphone also, via “Power”.

Via the “Settings” menu

In order to turn off the iPhone 10, the user needs to go to “Settings”, then go to the “General” panel. Go down to the bottom of the menu and press the inscription: “Turn off”.

How to turn off iPhone 5

The iPhone 5 and 5S were considered the most stable models and were popular for a long time. They work great, almost match the latest phones.

Two buttons

On gadgets up to Iphone 7, SIMultaneously hold down the “Home” and “Power” keys for 2-3 seconds. The phone will automatically reboot without any sliders. The device turns on via the “Power” key. When downloading, you will need to enter a password.

There is no Home key on models 7 and up. Instead, hold down the volume up or down button along with the power off key. iPhone will start to restart.

READ  Xiaomi phone screen goes blank quickly how to set up

Why the iPhone screen won’t turn off automatically and what to do?

All fiery categorical greetings! Constantly active backlighting of the screen can become a rather big problem. after all, the fact that the display does not turn off automatically leads to a variety of inconvenient things. Which ones? But for example: very fast battery consumption, strong heating of the device, and in general it is terribly annoying, since it is almost impossible to operate an iPhone in such a state!

No, of course there is one win-win option. put the smartphone on charge and never unplug it from the outlet. How do you like that? I do not like. Much better. once and for all deal with the always “on” display of the iPhone. This is what we will do with you today. Are you ready? Reade set Go. Let’s go! 🙂

What situations can cause the iPhone screen backlight to be constantly active:

  • Mechanical damage. fall, impact, other deformation of the case.
  • Poor quality repairs or components. For example, let’s take the iPhone 4 model (yes, it was a long time ago, but for an example it will do). Often, when replacing the screen in this model, they forgot to install (they did not know about it at all, it was too lazy to look for) the so-called uv filter for the light sensor. Because this thing came only with the original sensor (which comes from the factory), and the one that was installed instead of it was without this filter. Accordingly, due to its absence, the proximity sensor worked “anyhow” and the iPhone screen did not go out on its own during a conversation.
  • Moisture and other troubles can also lead to malfunctions of the backlight.

But you never know what else can be! Let’s take a better look at all the ways to solve the problem of the iPhone screen not dimming. So, here are the actions that are universal and suitable for each case:

  • Hard reboot. To do this, hold down and hold two buttons. HomePower (for iPhone 7 and older. the volume down and power button) until a complete reboot.
  • Updating or restoring software via DFU, after that it is important not to restore the backup and observe the behavior.

Now let’s move on to special cases. There can be two of them:

  • The display does not go out during a call.
  • Does not lock automatically, does not turn off the screen after receiving a notification or in standby mode.

IPhone screen not dimming when talking? Decision!

First of all, take a close look at the front of the gadget. Do you see films, glasses, covers on it. covering the front side of the iPhone? Even if they seem completely transparent to you, it makes sense to get rid of them and test the operation of the light sensor without such accessories.

If this did not help, and all the previous tips (reset, reboot, restore) were followed, then most likely the matter is in the light sensor. He could just “move away” or break.

That is why, when you bring your phone to your face during a call, your iPhone does not know that it needs to turn off the screen and this does not happen. There will be only one solution. replacing the proximity sensor. Fortunately.

IPhone display does not turn off after receiving a notification or SMS

The situation is as follows. a notification comes to the locked iPhone, the display naturally lights up, but later it does not go out automatically, and you can turn it off only by pressing the lock button. I know from myself. terribly annoying, especially at night. Received a notification when you sleep, wake up. and the phone is completely discharged.

I’ll tell you right away and please. the problem, most likely, is in the software. This means that there is a chance to fix everything without going to the service center. What can be done:

  • First of all, go to Settings. General. Auto-lock. If it is set there. “never”, then this is precisely the reason that the screen is not automatically locked. Set the exact time interval (by default it is 1 minute).
  • Next, you should follow the steps that are indicated at the beginning of the article, namely a full reset and restore the firmware. But there is a small “hitch” here. such actions are not always convenient to perform, and it takes a long time. Therefore, you can do this.
  • Remember which games and applications you have installed recently and uninstall them one by one and check if the situation has changed for the better. And of course, if you have a jailbreak on your device, then you should also pay attention to those tweaks that are installed, they can certainly lead to the fact that the screen will not go blank.

Finally, I would like to note that you should not forget about the warranty (which in some cases is two years!) And if you are too lazy to look for the cause of the breakdown yourself, feel free to bring it to the workshop. let them figure it out themselves, and in case of problems with the hardware of the gadget, the SC will SIMply give a brand new device for you. You need to know your rights! 🙂

Typical signs of such a breakdown:

iPhone touch screen turned black during bootup;

when you restart your smartphone, the problem persists, the screen is still black;

you cannot receive a call, the screen does not respond to pressing;

black screen on iPhone appears when entering the camera app;

stripes appear on the dark screen, but the phone continues to receive calls

The first thing to do if your iPhone has a black screen is to restart your device. If that doesn’t work, the problem is more serious.

When iPhone won’t turn on due to full battery drain

Full Battery Drain Another reason iPhone has a dark screen is when the battery is completely drained. If you used the gadget in the cold, and after that found that it went out and does not respond to attempts to turn it on, follow the following aLGorithm:

  • warm the device in your hands
  • connect the device to the charger
  • wait 15 minutes

After that, the download should start automatically. If this does not happen, check if the charging is working properly. It might be worth replacing it.

The screen freezes when the software crashes, what to do?

A black screen is usually caused by a hardware issue in your iPhone, so it is usually not a quick fix. The first thing to try to solve this problem. this apply a hard reboot

To perform a hard reset, press and hold the Power button and the Home button (round button below the display) at the same time for at least 10 seconds. Live until the Apple logo appears on the screen.

On iPhone 7 and 7 Plus, you need to do a hard reset by pressing and holding the Volume Down and Power buttons at the same time until the Apple logo appears.

On iPhone 8 and 8 Plus, X, you need to press and quickly release the Volume key, then press and quickly release the Volume button, hold down the Power button until the Apple logo appears.

If the Apple logo appears on the screen, most likely your iPhone is not a problem. it was a software glitch. Read on for what to do if the Apple logo doesn’t appear on the screen.

Mechanical damage is a reason to contact the service

As we said, there are probably two main reasons why your screen went dark. The first is if the cable that connects the LCD display to the logic board has disconnected (moved away) when dropped, the second. the display itself is broken. Only experienced service technicians can determine the exact cause. The service center “iMobi” will conduct a free diagnosis of your device and tell you exactly what kind of repair you need.

If the problem is with the cable, then this fix is ​​relatively SIMple: the wizard will open your iPhone and reconnect the digitizer cable to the logic board.

If the LCD is broken, that’s another story, but doable. Replacement of the screen (display) iPhone (Kiev) in the Apple service center “iMobi” will be done quickly and inexpensively using original spare parts.

What to do when your iPhone is on but the screen is black.

Even the highest quality smartphones periodically fail. any user can suddenly face such a problem as a black screen on the iPhone. You have rebooted your iPhone, connected it to the charger, and your iPhone screen is still black, take your time to get upset. Perhaps, restoring the device is not as difficult as it seems at first glance. Various breakdowns can lead to the appearance of a black screen, which in some cases can be fixed by yourself.

In this article, we’ll explain why your iPhone screen won’t turn on and what you can do to fix it.

Why does iPhone have a black screen

Black screen on iPhone can be for a variety of reasons. from hardware glitches to firmware issues.

Typical reasons why the iPhone screen won’t turn on:

  • If the phone is dropped on a hard surface or other mechanical damage that may damage the display, the flex cable may come off.
  • Full discharge of the smartphone, which can lead to the fact that the “apple” device stops functioning. vibrate, transmit signals, show an image of an apple, etc.
  • There is a bug in a specific application. In this case, the display darkens when you enter this application.
  • A failure occurred during the download phase. At the same time, the apple icon is constantly on the screen and nothing else happens.

Force iOS update

The firmware update usually takes about 40 minutes. After the performed procedure, your iPhone and display should take some time to work. It usually takes up to 40 minutes for iOS to download from Apple servers. Usually, an emergency reboot of the device helps to cope with any failure during the firmware update, but if this does not happen, try entering DFU Mode and resetting the settings to factory settings.

Black iPhone screen due to mechanical damage? Let’s take a look inside.

A quick look at the inside of your iPhone will help you understand why your screen is black. There are two hardware we will talk about: your iPhone’s display and the logic board.

READ  A stripe appeared on the screen of the Honor phone

Logic board. these are the brains of your iPhone, and every part of it connects to it. The display shows the images you see and it is the logic board that tells you what to display.

Your iPhone’s entire display is removable, but much more complex than you might think! There are 4 main components under the display:

LCD screen displaying the images you see on your iPhone;

a digitizer that is part of the display that processes touch. It digitizes your finger, which means it turns the touch of your finger into digital language your iPhone can understand;

Each component of your iPhone display has a separate connector that plugs into the logic board. This is why you can swipe your finger across the screen even though the screen is black. Digitizer works, but LCD doesn’t work.

Basically, your iPhone screen turns black because the cable that connects the LCD display to the logic board is disconnected. This cable is called the display data connector. When the display data connector is displaced from the logic board, your screen becomes inoperable.

There are other options for the reason for the black screen of the iPhone, for example, when the LCD itself is already damaged, and then it does not matter if the display is connected to the logic board or not. it is broken and needs iPhone screen (display) replacement

iPhone frozen and won’t turn off or restart

Usually, if the iPhone freezes, users try to turn it off or restart using the standard procedure, namely by long pressing the Power / Lock button. Unfortunately, in most cases, when the iPhone freezes, this shutdown method does not work. iPhone keeps running and running frozen apps no matter how long the user presses the power button.

But, the iPhone has an alternative shutdown method that bypasses the iOS operating system. Thanks to this, this shutdown method works even on tightly frozen devices. The method consists in SIMultaneously pressing the “Home” button and the Power / Lock button.

Home and Power Buttons

The Home and Power buttons must be pressed SIMultaneously and held until the frozen iPhone turns off. After turning off, you need to wait a few seconds and make a short single press on the power button. After that, the iPhone will turn on and start working normally.

It should be noted that the key combination “Home Power on” is also responsible for taking a screenshot. But, to get a screenshot on these keys, you need to press literally for 1 second, if you hold the keys longer, then the anti-freeze protection will work and the iPhone will reboot.

If you have an iPhone X or newer, then you need to use the new reboot method.

What to do if iPhone is frozen

Freezing is a problem that any computer hardware faces. At some point, one of the programs begins to behave incorrectly or conflicts with another program, and as a result, the entire device is inoperative. This situation is called freezing.

iPhone is also prone to this issue and may freeze from time to time. Usually, when the iPhone freezes, it refuses to turn off or restart, which baffles the user. Most often old models freeze, such as iPhone 4, 4s, 5, 5s and 6. But sometimes even iPhone 6s and 7 users face freezes.

If you find yourself in such a situation, then this material should help you, here you will learn what to do if your iPhone is frozen.

iPhone freezes when turned on

Pressing the Power On Home buttons at the same time allows you to turn the device off and on in any situation. However, this procedure does not guarantee that the iPhone will not freeze again during the startup process.

If your iPhone freezes before the device is fully loaded, then you can use the recovery mode called “Recovery Mode”. With it, you can restore your iPhone to its original state and bring it back to life. But, it should be borne in mind that this procedure is equivalent to a reset to factory settings and leads to the deletion of all user data.

In order to enter Recovery Mode on iPhone and perform recovery, you need to do the following:

  • Turn off your iPhone and wait a couple of minutes for all programs to finish their work. If the iPhone does not turn off in the standard way, then you can resort to the combination “Turn on Home” described above.
  • Then you need to press the “Home” button and without releasing it, connect the iPhone to the computer via the Lightning cable.
  • Once connected, keep holding the Home button until the iPhone displays the iTunes logo and cable image.
  • Now you need to release the Home button and start iTunes on your computer.
  • In the iTunes program, go to the iPhone settings and click on the “Restore iPhone” button.

Restore iPhone button

Thus, you can solve the problem with the iPhone freezing during startup, but, as already mentioned, for this you will need to donate all user files. You can read more about Recovery Mode in our article on resetting iPad to factory settings.

Also on Apple devices there is a so-called DFU mode or Device Firmware Update. If recovery mode does not help, then you can try to enter iPhone into DFU mode and try recovery again.

What to do if iPhone screen is black and won’t turn on

“Black screen is on” and no response from iPhone 6, iPhone 5s, iPhone 7, iPhone 6s, iPhone 5, iPhone x is not a rare problem among Apple phone users.

Although it looks “formidable”, it is usually very easy to solve. See below what to do with such situations.

If your iphone 5s, iphone 6, iphone 5, iphone 7, iphone x, iphone 4s, iphone 6s, iphone 4, iphone 7 plus, iphone se stopped responding to attempts to bring it into working order and shows its opposition using the so-called “ black screen “, this is not a reason to send it for repair.

There is a SIMple and quick way to bring him to life using a special computer program.

Program to fix black screen in iPhone

There is a great program that can turn on the iPhone even if the buttons don’t work. It’s called “ReiBoot”. Installed on a computer. The translation is really a little lame, but you can figure it out. You can download it here.

iphone, screen, turn

In addition to turning on / rebooting, many solutions are integrated into it to fix errors that have arisen in the firmware.

In particular, elimination of freezes on an apple, problems with a black screen, splash screen, death screen, connecting to iTunes and many others.

The program has been verified. I recommend, although it is not a fact that it will help you, since of course it will not fix hardware problems.

Another solution when iPhone won’t turn on

This solution is slightly different for different iPhone models. precisely, the way of its implementation differs.

Try in smartphones 4S / 6S SIMultaneously press “HOME” (bottom on the screen) and “POWER” (side on the case) for 15-20 seconds, and in 7 models POWER and Volume.

In 8/10 models, quickly press and release the “Volume up” button, then do the same with the side button (POWER).

If successful, the screen should display the “burning apple” logo. Release buttons and wait for launch.

I don’t know why, but it helps many to turn on / off the silent mode switch several times before performing the steps above (if holding HOME and POWER is ineffective).

If these recommendations above did not give a successful result, then it is not unfortunate, but the reason may be physical damage to the components.

You can only replace the cable or charger on your own, but it is better to entrust the “insides” to specialists.

NOTE: it has been noticed that sometimes the smartphone does not charge from the charger, but it is charging from the computer or laptop. I recommend you try and see for yourself. Success.

Other Ways to Solve Black Screen Problem in Iphone

If the phone is still unresponsive and the black screen persists, connect the phone to the charger and press two buttons at the same time: wake / standby and start button.

Hold the buttons for about 10 seconds until the Apple logo appears on the screen. In some cases, you may also see a battery icon, which means you need to charge your phone.

A completely discharged battery is the most common cause. In rare cases, the firmware may fly off.

Connect your smartphone to a charger or to a computer / laptop and leave for 30 minutes. If the reason is in the battery, then after half an hour of charging it will definitely turn on.


hello, my 4S iPhone shows to connect the charger, stood the night! but it didn’t turn ON, pressed both HOME and ON keys, the white screen just blinks and everything from the beginning, the phone is 1.5 months old, what is the reason, the block is normal, the phone is not sees

| Contacts | Content | RSS