Osd Locked On The Monitor How To Remove

6 answers

According to the aoc page. you need to do the following for one of the displays

If it doesn’t work, try to find your screen on the page. Or check the manual you received with the monitor.

OSD Lock Function:

To lock the OSD, first turn off the monitor by pressing the power button, and then hold the left button for 5 seconds and simultaneously press the power button with the left button, and the osd is locked.

OSD UnLock Function:

To lock the OSD. repeat the above process and then the OSD is unlocked

Mine is AOC. I did this: first turn off the power button and then press the power button and menu together, if the OSD lock message appears on the screen then it doesn’t work, but if not, then it worked. I experienced it myself.

I also got into the same problem, I realized that different configuration is different for different AOC models, you better take a close look at your manual.

In my model, as stated in the manual, while the monitor is off, press the left button and press the monitor power button to lock / unlock the osd. [I know the post is older, just writing an answer, maybe it helps someone.]

To unlock the OSD lock, press and hold the menu button for 10 seconds and the menu will appear. To lock the OSD, press and hold the menu button for 10 seconds.

lesson: How to unlock the buttons of the Philips monitor

Do you get “Buttons Locked” when you press any button on the PhilIPs monitor? There are solutions depending on what caused the buttons to be locked. They will be discussed further.

Like any malfunction, if it is a failure in the software settings or a malfunction in the hardware of the electronics, it is necessary to identify the causes or the damaged module. We recommend that if you need serious procedures. firmware firmware or parts repair, contact the PhilIPs service center professionals. This will protect you from the consequences of inept independent actions.

Monitor controls locked philIPs how to remove

Such is the problem when you press any button on the monitor panel, the OSD main controls is locked message pops up. Also, such an inscription can pop up by itself. Frequently seen on PhilIPs 150S4 monitors.

The problem is in the buttons on the monitor’s control panel, they are produced over time and work on their own, or when pressed, the wrong buttons are triggered, or several buttons are pressed simultaneously and the menu is buggy.

My AOC 21 ‘monitor has an On-Screen Display, but I’m wondering how its lock function works.

Can you help me figure out how to lock and unlock the OSD?

Reasons and solutions

The most likely and easily remediable cause is accidental blocking as a result of your touching the sensor. Many people consider the location of the touch buttons on Philips monitors Not very convenient and often face the fact that the buttons are triggered every other time and do not have a night backlight.

Osd Locked On The Monitor How To Remove

So, if the reason lies in an accidental blocking, you can easily handle it yourself. To do this, first press the “Menu” touch button, then hold the “OK” button for 20 seconds. The lock will be successfully released.

If the above manipulation did not bring the desired result, you cannot do without service center specialists. The most likely prerequisite for why the buttons do not respond to your commands is sensor failure. You should also check wiring and connectors for dirt and damage. If necessary, replacement of non-working parts is required.

Osd locked on the monitor how to remove

OSD stands for On Screen Display. This is an OSD configuration menu included in various displays. When you press the MENU button or one of the other buttons on the front or side of the monitor, it may also appear.

Osd Locked

Osd Locked typically includes monitor calibration options such as brightness, contrast, and color settings. Some configuration menus may also include horizontal and vertical position controls, tilt and keystone adjustments.

READ  How To Configure Hertzovka Monitor Windows 10

If you are unable to adjust the monitor settings using the OSD, the OSD may be locked. You may also see the phrase “OSD Locked” when trying to change settings. Some monitors include an OSD Lock option that you can turn on or off. If this option is available, simply Disable OSD lock and you can make changes to the settings.

If your computer does not have a “lock” option, you can unlock by pressing and holding MENU on the front or side of the monitor for a few seconds.

Osd Locked is used to describe the physical menu buttons located on the computer monitor. By combining the many settings found in the operating system and the Customizable Settings created using on-screen buttons, users can create their own personal Nirvana views. Computer manufacturers create a lock feature to save THESE custom display settings.

A message appears when a specific OSD button is held down for a specified period of time, usually 10 seconds. When OSD lock is activated, buttons will not respond. This is usually done on purpose, to ensure that there are no accidental changes to the display settings, it can be activated accidentally if something is pressed against a certain button.

Most likely, he annoyed many of you at some point. You turn on your monitor one day and you see an incomprehensible message telling you in OSD Lockout. It does not allow you to change any of your display settings, including options designed to disable this message. Mostly this error occurs on HP monitors, but it also turned out that they are faced with it on second brands. The Fixes Submitted Should Work On THESE Monitors.

How to remove instructions

  • Shut down the computer completely, and then disconnect the monitor cable from the port on the back of the computer. Reconnect the cable and make sure the pins are properly tightened. Turn the computer back on and check if the message stating that the display is locked is still displayed.
  • Check the manual that came with your computer or monitor and look for the troubleshooting section if you’re still getting the lock notification. Look for the OSD lock header and read the method your specific monitor model uses to unlock. Follow the instructions to unlock the display.
  • Try following the general unlock steps if you no longer have the instructions that came with your monitor. Press and hold the Menu button located at the bottom of the monitor for 15 seconds and wait to see if the message disappears into the lock.
  • Press the Menu button again if the lock message remains on the screen. Use the arrow buttons to navigate through the main menu items. Highlight Settings or OSD Menu and then press the Menu key again to access a new list of settings.
  • Scroll down to the Blocked heading. Use the arrow keys to change the setting to “Net”. Press the Menu button again to return to the main menu. Go to the Exit setting and then press the menu key one last time to exit the menu setting and release the lock.

How to enable Osd Locked

Your monitor may have a MENU lock function. This feature locks out most OSD settings so they cannot be changed unintentionally, usually allowing you to adjust brightness, contrast, channel, and volume. To lock, unlock OSD, see below:

Method 1:

Depending on the model, you may need to press and hold the “Menu” for five seconds or the “Source” button.

On models with the Jog key on the back of the monitor, you can unlock the OSD by pressing the LEFT key for ten seconds while the main menu is displayed.

Method 2:

To restore the OSD to factory defaults, read the complete user manual (available in the Download Center under Support).

Osd locked on the monitor how to remove

How to install and configure the recorder

Customers who bought cameras and recorders often DO NOT understand how to connect and configure them by themselves. Although it is not difficult at all, and so you do not have to pay for calling a specialist.

So, let’s try to tell you in a simple and accessible way how to set up the recorder.

READ  How To Make A Call Photo In Full Screen

Let’s look at Turbo HD (TVI) cameras and DVRs first. There will be two options:

1. Connecting the camera to the recorder, and then to the monitor (view only from this monitor):

2. Setting for viewing from computers on the local network and Internet access. This means that you can view from anywhere with a PC and the Internet, even from a mobile phone:

Before the whole procedure of connecting with the recorder, it must be unscrewed (at the bottom there are 4 screws on all models, and on some 2-3 more from each side at the attachment points of the rack corners) and place the hard drive there, connecting it with the wires that come with the kit (also like a computer) and put it back together.

After unpacking the camera, we see three screws with dowels (it’s understandable why) and, in fact, the camera itself with two plugs. The first one is connected to a 12 v power supply (unfortunately, it does NOT come with the camera). Second. to connect to the registrar. for this we need a coaxial cable and two BNC connectors (not included).

Using three dowels, install the camera in a suitable place selected for it and extend the cable to the recorder.

The coaxial cable for each camera needs to be stripped on both sides. In a nutshell: there is a copper core inside the cable, cutting off everything that goes on the floor of this core (insulation, braid, second insulation) to expose it by 5-6 mm.

The most convenient way to do this is using a special “clothespin knife” (Cutting tool for coaxial cable), well, or an ordinary cutter (stationery knife. Just be careful).

We will mount BNC connectors to these cleaned places.

We use quite convenient BNC-spring connectors.

Next, we untwist the BNC connector and see a very simple picture there. there is one small screw, which is screwed perpendicularly into a copper tube, into which we insert our cable core.

We unscrew this screw a little, insert the core and clamp the screw back, the cable insulation floor turned out to be some metal “ears”, we crimp them with pliers so that the wire is securely held in the connector. cord ready.

We connect one side of it to the camera plug using the method “insert and scroll”. Rotate the top of the connector to securely attach the plug. We also connect the second side to the recorder in one of the 4/8/16/32 slots, under which it is written “in”.

The situation with the network recorder is much simpler. IP cameras are connected to the second connector by a standard Ethernet patch cord with RJ.45 connectors on both sides to the switch, like the recorder itself. We will NOT describe how to make such patch cords, such information is very common on the Internet. If the switch has PoE (Power over Ethernet) or such a switch is built into the DVR itself, then it is NOT required to connect power to the first connector of the camera.

However, with an NVR (network recorder), it is not enough just to connect the cameras to the switch or to the PoE interfaces of the recorder itself. they need to be registered in it, a link on how to do this will be given below in accordance with the procedure.

Next, connect the 12 / 48v power supply (which is included in the kit) to the recorder into a socket labeled 12v or 48v, respectively. Connect a mouse (included) to the USB and connect the monitor to the DVR using a VGA cable or HDMI cable. You can also connect to the Turbo HD recorder using a coaxial cable, where on one side there is a BNC connector, and on the other RCA (tulip), a TV.

turn on the registrar

In order to understand. how to set up the registrar. you need to turn it on first. At this moment, the recorder may start beeping (beeping). This can happen for a reason if you forgot to insert, for example, a hard disk into it. We will tell you a little later where to find the cause and how to turn off the annoying beeping.

So, we activate the device, enter the password for the admin user. Upon request, you will need to enter a password, whatever you come up with. the harder the better.

READ  How To Remove A Dead Pixel On The Monitor

The user must enter the administrator password. You need to come up with a password yourself and it must contain from 8 to 16 characters. The password should be carefully memorized or written down in a safe place, as the reset procedure is extremely time consuming and laborious!

After entering the password, many registrar for ease of maintenance is prompted to enter a graphic password, but there, I think, you will figure it out.

then there will be a question whether to launch the assistant?

In this window, be sure to uncheck the box next to the “Run the assistant when you turn on the DVR” item, because we will definitely not do the setting every time. But the first time you can use it. click “track”. and windows with basic settings will appear on your monitor in turn.

Configuring the time zone, time and date.

After that there will be a window with network settings. For normal operation, Not only the IP address and subnet mask must be registered, but also the gateway and DNS. What it is and how it is determined, we will NOT touch here either, because such information abounds on the Internet, the main thing is to understand that the registrar. it is the same computer as a regular PC or laptop in terms of network configuration.

It is quite enough to Get automatic settings from the router (server) by ticking the “DHCP” box, but for this, the DHCP server must be set up in the local network (most often it is turned on either on the Internet access router or on the corporate channel server).

Next comes the cloud settings. Nowadays it is more often called Hik p 2 p Cloud. not EZVIZ.

Here you can leave the default settings, only enable if you plan to view cameras from the DVR from mobile devices.

Connection ports. In this section, the ports for network access and settings for access via DDNS are registered. We recommend leaving all settings unchanged.

Next is the turn of the hard drive, in this window it can be seen, identified and formatted.

Initially, hard drives are delivered NOT formatted. In the case of installing a hard drive, which has already been used, it is still recommended to format it. To do this, press the “initialize” button.

After that, there may be other windows or series of windows for setting depending on the model of the recorder, for example, the series “Enable RAID, Manage arrays Manage hard disks” (but then instead of the previous one)

or the series “Search and connect IP cameras from the online list, Camera recording settings, Copy recording settings”. How to do this, see the article “ How to Add Camera to NVR “.

The next setting window. The recording mode will appear only if the series of IP cameras from the online list has not been provided. In this window, you can enable recording for all channels by motion or continuous. Most often, users choose motion recording to save hard disk space. In the basic settings, a segment is included in the archive. starting 5 seconds before the start of the movement in the frame, and ending 5 seconds after it ends.

This completes the initial setup of the registrar, and the assistant will be closed. The image will change to a quad screen, which may not have displayed cameras if it is NOT a DVR.

Let’s go back to the sound signals of our recorder, go with the right mouse button

at “Main menu” → “system config” → “warnings” and see their options (the reasons for the beeps). lack of HDD, etc., There are three types of alarm notifications in total: sound, sms, email. Uncheck / check the boxes “sound signals” and click “to apply”. Set up other notifications in the same way.

Main menu

warnings

If our NVR or we want to connect some number of supported IP cameras to the DVR. then you need to register these cameras manually. How to do this, see the article “ How to Add Camera to NVR

After completing the connection of cameras, click on the button “Live View” in the lower left corner of the screen and go to display.

| Contacts | Content | RSS